棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

稳定同位素井间示踪技术在深层块状稠油油藏水驱特征研究的应用

经对冷43块深层块状普通稠油水驱注水5个试验井组开展的稳定同位素示踪测试，利用中子活化技术分析样品，采用先进的示踪剂定量分析与流动模拟相互结合的方法，以示踪数值模拟为手段，评价了油井连通、油层平面及纵向上的非均质性、隔层的封隔性等因素对水驱控制程度及动用状况的影响，通过优化注水推进方向及速度，强化动态调整措施，提高了稳产基础。     

基于B/S的网上教学系统

利用ASP技术与ADO技术,采用Browser/Server模式设计了一个网上教学系统,它包括网上报名、网络课堂、在线答疑和师生信箱.用户可通过交互式动态形式来学习课程内容、进行随机抽取试题、即时打分、查看以往成绩、修改个人信息记录等功能.     

Characterization of two-phase nickel aluminides produced by pressure-assisted combustion synthesis

Two-phase (B2+L1₂) nickel aluminide intermetallic compounds were synthesized by the pressure-assisted volume combustion synthesis (CS). The production and characterization of the samples containing NiAl+Ni₃Al were investigated. Aluminum (99% pure, 15 μm) and carbonyl nickel (99.8 pure, 4-7 μm) powders were used. The production of intermetallic compound was carried out at 1050 °C under 150 MPa uniaxial pressure in open air atmosphere in an electrical resistance furnace for 60 min. The formation temperature of intermetallic compound was determined by differential scanning calorimeter (DSC) analysis, and exothermic temperature of powder mixture was determined as 653 °C. The characterization of samples was confirmed by optical microscope, SEM and XRD analysis. It was observed that the structure of compound has very low porosity and the formation of NiAl was completed successfully. The relative density of test materials measured according to Archimedes’ principle was 98.04%. The microhardness of test materials was about 351 HVN₁.     

泥土中微量六氯环戊二烯的气相色谱分析

采用SE 3 0为固定液进行色谱柱分离 ,用外标定量法测定泥土中的微量六氯环戊二烯 ,结果最小检知量为 0 .18× 10 - 6 ,相关系数为 0 .99992。     

巴彦浩特探区钻井液技术初探

巴彦浩特探区钻井液工艺技术的重点是，解决疏松砂砾岩地层水涌漏同层、侏罗系地层水的HCO3^-污染及可能出现的火成岩地层井塌复杂。结合内蒙古巴彦浩特探区地层和井身结构特点，采用了两性聚合物／氯化钾钻井液和氯化钾／石膏-聚磺钻井液体系。该体系抑制能力强，性能稳定．容易实现低固相、低密度近平衡钻井，保护储层效果好。对复杂情况采取了有针对性的处理办法：平稳操作和合理的钻井工程措施是预防水层涌漏同层和火成岩井塌复杂的重要手段；用井场易得的固井水泥或石膏配合烧碱处理HCO3^-污染简便易行；处理火成岩井塌复杂，控制合适的钻井液性能是必要的。     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

纤维体积分数对K3D/MCPA复合材料力学性能的影响

本文研究了纤维体积分数对三维编织芳纶纤维增强铸性尼龙(简称K3D／MCPA)复合材料力学性能的影响。研究表明，K3D／MCPA复合材料有优异的抗冲击性能，冲击强度比三维编织芳纶纤维增强铸性尼龙(简称C3D／MCPA)和纯基体均有大幅度的提高，且随着纤维体积的提高而升高。K3D／MCPA复合材料剪切强度随纤维体积比的增大而增大，其纵向剪切强度低于纯基体和C3D／MCPA复合材料，但其横向剪切强度高于它们。K3D／MCPA复合材料弯曲强度与弯曲模量随纤维体积比的提高而提高，但与相同体积比的C3D／MCPA相比，K3D／MCPA的弯曲强度与弯曲模量均较低。