在SNMPv3体系结构下计费模型的实现

提出了一种在SNMPv3体系结构下实现的计费模型，讨论了其PDU格式，计费过程和SNMP实体的结构，该模型对现有SNMPv3体系结构作了最小的改动，它的提出增强了SNMP的重要性，扩展了SNMP的应用范围。v     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

激光水下成像技术及其进展

介绍了近年发展起来的三种主要的激光水下成像方法，即常规水下激光成像、高分辨率水下激光三维成像和偏振激光成像，分析了它们各自的工作原理、特点以及各自的发展状况。     

凝胶成型法制备加氢催化剂载体的研究与工业化生产

采用凝胶成型法制备加氢催化剂载体，并进行了工业放大试验。通过BET、NH3-TPD、H2-TPR等表征手段及实际的加氢反应性能评价对凝胶成型法制备的载体及加氢催化剂与常规方法进行对比分析，结果表明，采用凝胶成型法所制得的载体及催化剂均具有较高的孔体积和比表面积、较低的堆密度，其机械强度可满足工业要求，总酸量及中强酸酸量得到提升，催化剂活性组分与载体强结合力得到削弱，金属利用率提高，应用性能明显优于传统方法制备的加氢催化剂载体。通过该方法完成了加氢催化剂载体的工业生产，所生产的载体应用于天津院THDS-3加氢精制催化剂取得了良好的工业应用效果。     

数字下变频器GC1012B原理及配置方法

数字下变频技术是软件无线电的一项核心技术,其性能的好坏直接影响数字接收机的精度。GC1012B是美国TI公司推出的新型数字下变频器。文中从GC1012B的结构特点和内部功能框图出发,分析其工作原理,并介绍GC1012B几个主要寄存器的配置方法,从而实现对频率、滤波模式、增益大小等参数的设置。最后给出了一个具体配置实例作为参考。     

Fe3O4/PSt/TiO2多层包覆电磁响应微球的制备

首先采用分散聚合法将自制的Fe3O4磁流体和苯乙烯反应合成有磁核的Fe3O4/PSt磁性聚合物微球，然后，用非均匀成核水解反应在Fe3O4/PSt微球外包覆无定形二氧化钛，获得Fe3O4/PSt/TiO2复合微粒。用红外光谱、扫描电镜和热分析对粒子的形貌和结构进行了表征。并测试了微粒的介电性能和磁性，结果表明，所制得复合微粒有良好的电、磁响应性。     

Range of the Applicability of the Wilkins Method to the Investigation of the Dynamic Stress-Strain State of Anisotropic Elastic Axisymmetric Shells

The exactness and stability of the Wilkins method in the investigation of the stress-strain state of axisymmetric anisotropic elastic shells, including thick-walled ones, have been studied for different values of artificial viscosity, pulse load rise and fall time, and different deformation process durations. A comparison of numerical calculations, performed by means of an application software package developed by V. A. Romashchenko on the basis of the Wilkins method, with experimental results, known numerical data, and with calculations using the computation kernel LS-DYNA 3D has been carried out.     

用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再