Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.     

用介孔材料制备定向碳纳米管的研究进展

综述了近年来采用介孔材料制备定向碳纳米管的研究进展,包括介孔材料的合成及介孔材料在制备定向碳纳米管方面的应用。重点介绍了采用合成介孔材料的模板剂石墨化及介孔材料作为载体制备定向碳纳米管的方法,探讨了模板剂种类、催化剂的制备方法及反应温度和时间对定向碳纳米管生长的影响和定向碳纳米管生长的介孔限制机理,并提出了这一领域的研究方向。     

低k氟化非晶碳层间介质对芯片性能的影响

讨论了通过合理设计的工艺流程将低k氟化非晶碳材料应用到制造工艺中作为互连介质对集成电路性能的影响。基于一个互连结构简化模型计算出采用低k氟化非晶碳材料作为互连介质后RC延迟、功率耗散和线间串扰的变化情况。采用低k氟化非晶碳介质后,RC延迟和功率耗散随着互连长度的增大而减小,线间串扰也得到显著抑制。     

Methane/natural gas storage and delivered capacity for activated carbons in dry and wet conditions

Methane/natural gas storage and delivered capacity for three different activated carbons in dry and wet conditions were measured. In all tests the temperature of the bed was maintained constant at 277.15 K and pressure was increased up to 10 MPa. Natural gas storage capacity was less than methane storage capacity in dry conditions for all the three activated carbons tested, while the gas delivery was almost the same. One of activated carbon tested (NC120) showed the possibility of hydrate forming for pressures higher than 4 MPa but the amount of gas stored still was less than the amount stored in dry conditions over the whole range of pressure. The analysis of the gas delivered at each pressure steps shows that considerable amount of heavy components do not come out from the bed even at very low pressures in both dry and wet condition tests. Repeatability of the sorption/desorption processes - vital for possible commercial/industrial use - has been examined over various cycles.     

A disposable sensor based on immobilization of acetylcholinesterase to multiwall carbon nanotube modified screen-printed electrode for determination of carbaryl

A simple method has been devised for immobilization of acetylcholinesterase (AChE) covalent bonding to a multiwall carbon nanotube (MWNT)-cross-linked cellulose acetate composite on a screen-printed carbon electrode (SPCE) and a sensitive and disposable amperometric sensor for rapid determination of carbaryl pesticide is proposed. The immobilized enzyme was preserved on this film because of the excellent biocompatibility and non-toxicity of cellulose acetate. Based on the inherent conductive properties of the MWNT, the immobilized AChE had greater affinity for ATCl and excellent catalytic effect in the hydrolysis of ATCl. MWNT improved the interface enzymatic hydrolysis reaction and increased the amperometric response of the sensor. Under optimum conditions, the inhibition of carbaryl on AChE increased linearly with the increasing concentration of carbaryl in two ranges, from 0.01 to 0.5 μg mL⁻¹ and from 2 to 20 μg mL⁻¹, with the correlation coefficients of 0.9985 and 0.9977, respectively. The detection limit was 0.004 μg mL⁻¹ taken as the concentration equivalent to 10% decrease in signal. The sensor showed acceptable stability, accuracy and could be fabricated in batches, thus it is economic and portable. This type of disposable enzyme-based amperometric sensor has extensive application potential in environmental monitoring of pesticides.     

Influence of pencil lead hardness on voltammetric response of graphite reinforcement carbon electrodes

This work studied the voltammetric response of graphite reinforcement electrodes made of different pencil lead hardness. The studies showed that harder graphite leads, regardless of their manufacturer, are more appropriate as electrode material for voltammetric purposes due to their higher peak currents, increasing sensitivity and reproducibility, with ΔEp closer to the theoretical value for a reversible system.     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

130t RH脱碳模型建立及超低碳钢处理工艺优化

建立了RH真空处理脱碳数学模型，并通过130t RH工业试验结果对此数学模型加以验证。根据模型分析了[C]0、[O]0、真空度、提升气体流量等对脱碳效果的影响，据此优化了处理工艺，取得较好的效果。     

剖析全板电镀镍金发白现象

简要介绍了全板电镀镍金加工过程中镀金面发白现象及改善措施。特别是针对高位发白(或粗糙)的产生原因和处理过程进行较为详细的描述,并对工艺在此处理过程中存在问题进行了简要剖析。     

Continuous hydrogen evolution from cyclohexanes over platinum catalysts supported on activated carbon fibers

The continuous production of hydrogen from cyclohexanes is achieved effectively using Pt/ACF (ACF = activated carbon fiber) catalysts in a fixed-bed flow reactor. The Pt catalysts are more effective than a Pd/ACF catalyst for the reaction. Besides cyclohexane, methylcyclohexane, 1,4-dimethylcyclohexane, and p-menthane can also be employed as hydrogen source in the reaction system.