改性双马来酰亚胺的研究

本文研究了双马来酰亚胺与烯丙基化合物形成的改性树脂体系的固化和热性能，讨论了单体配比、增韧剂、催化剂对性能的影响。     

Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

ARAM·ARIES SPM-Lite便携式遥测地震数据采集系统简介

ARAM·ARIES SPM-Lite便携式遥测地震数据采集系统是加拿大GEO-X公司在2002年下半年推出的全新小型便携式地震数据采集系统。该仪器运用了当今最先进的计算机制造技术、网络化技术和微电子技术,除继承了ARAM-ARIES地震数据采集系统所有功能和技术外,它还简化了硬件结构,使体积更小,重量更轻,功能性更强。更加适应地矿、煤田、丛林和山区进行地震勘探。     

我国先进制造技术的现状和发展途径

介绍了现在制造业中面临的问题，通过对问题的分析，提出了发展先进制造前沿技术的见解和在我国发展先进制造技术的途径，同时展望了先进制造技术的发展前景。     

高炉煤气净化系统新技术研究与应用

济钢第二炼铁厂针对原高炉煤气净化系统处理能力不足等问题，研制了新的煤气净化系统。该系统采用单根文氏管、串联花环、丝网脱水器湿法除尘，取代原串联文氏管电除尘净化工艺。应用表明，新系统运行安全，净煤气含尘量小于10^mg／m^3，含水量小于5g／m^3，高炉风温提高90℃。     

Catalytic oxidation of sulphide ions to elementary sulphur in aqueous solutions over transition metal oxides

The catalytic activity of a wide range of transition metal oxides in oxidation of sulphide ions by air in aqueous medium was studied. Some specific features of the reaction mechanism on some of the studied oxides were considered. The transition metal oxides are promising catalysts for practical application. Some of these oxides will allow the preparation of catalysts possessing activity comparable to that of the cobalt phthalocyanine based catalysts, popular in industrial practice.     

Kelogg合成氨工艺进展

综述了以先进合成氨工艺和转化换热系统技术为代表的Ｋｅｌｏｇｇ第二代合成氨工艺。较详细介绍了钌基催化剂和转化换热器     

国产活性炭在合成气净化中的应用

选择国产Ｋ０１活性炭脱除羰基铁、镍，以达到保护铑催化剂并减少副产物的目的。１年的实际应用结果表明：国产Ｋ０１活性炭能够替代进口活性炭在合成气净化中应用。     

中国先进研究堆导流箱流场的数值模拟

采用目前国内普遍使用的计算流体力学 (CFD)软件PHOENICS 3 2对中国先进研究堆不同结构的导流箱的三维流场进行数值模拟计算。结果表明 :导流箱入口导流板和导流筒能显著改善导流箱入口冷却剂的流动状况 ,获得入口冷却剂沿周向均匀分流的效果 ,达到显著减缓入口冷却剂对垂直辐照孔道导管及安全棒导管直接的横向水力冲刷的设计目的     

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel are performed. The sizes of a regenerative heat exchanger and a boiler are expected to be smaller for He than for Ar. The pressure loss of a working gas in a regenerative heat exchanger is reduced for He. The purification subsystem for He is expected to be more compact and economical than that for Ar; but a larger compressor is required for He than for Ar.