从数字看发展片式电容器面临的机遇与挑战

采用海关进、出口统计和行业生产统计资料,通过计算、分析,用数字来说明国内发展片式多层陶瓷电容器、片式钽电解电容器、片式铝电解电容器、片式有机薄膜电容器所面临的机遇与挑战,并对其国内市场需求总量、额,国产品在国内市场占有率等做出评估,为有关单位了解片式电容器的发展提供参考,为国产产品更有效地进入国内市场、促进其发展提供依据。     

基于不同爆轰产物的格尼速度估算新方法（英）

A new method for prediction of Gurney velocity of explosives is introduced in which energy output is correlated with the heat of detonation, the number of moles of gaseous products of detonation per gram of explosive and the average molecular weight of gaseous products. It is assumed that the CHNO explosive reacts to form products composed of N2 , CO, H2O, CO2, H2,O2 and C（s） as determined by the oxygen balance of the unreacted compound. Good agreement is obtained between measured and calculated values of Gurney velocity as compared to previous correlations which assumed the reaction products to consist of N2 , H2O, CO2 and either C（s） or O2.     

黑龙江省"农业需水"初探

黑龙江省复种指致为1，推算农业需水为400～500mm，而多年平均年降水量多数大于400mm，有发展雨养农业可能；三江平原多年平均年降水量550mm，为此三江平原井灌区现有耕地具有全部发展种植水稻的可能。     

普通热轧钢材的合理洁净度及生产工艺探讨

钢凝固前、后生成的非金属夹杂物形貌和在钢中的分布特点不同,凝固前生成的夹杂物尺寸较大,在钢中随机分布,主要影响钢材的疲劳强度和延性等性能。凝固后生成的夹杂物尺寸小,主要在晶界富集析出。硅锰脱氧钢脱氧后钢液仍含有20×10-6以上溶解氧,这部分溶解氧在钢凝固后绝大多数会转变为微细的氧化物或氧硫化物夹杂。钢凝固后生成的夹杂物主要影响钢材的冲击韧性、韧-脆转换温度等性能。 对热轧长型材用普碳钢和低合金钢不必采用铁水脱硫预处理,对热轧钢板用普碳钢可采用铁水轻度脱硫预处理,对热轧钢板用低合金高强度钢可采用铁水脱硫预处理、炼钢过程抑制回硫和出钢过程脱硫的工艺。对超低硫低合金钢,在钢水炉外精炼脱硫处理过程钢-渣间须维持非常低的氧势,炉渣成分应控制在CaO:SiO2:Al2O3=60％～65％:4％-8％:30％～35％范围。 普通热轧长型材用钢脱氧后溶解氧含量可放宽至(30-50)×10-6,对中、厚板钢溶解氧含量必须较严格控制,最好采用铝脱氧将溶解氧控制在较低的水平,并将T[O]含量控制在50×10-6以下。采用降低炼钢终点钢水氧含量、出钢挡渣、CAS和CAB等较简易炉外精炼方法和防止铸坯夹渣等措施,能够生产满足普通热轧钢洁净度要求的高品质钢材。     

传统块状炭材料的发展概况

传统块状炭材料，如石墨电极、炼铝用阳极和阴极炭块、电炭制品、特种炭和石墨、炭砖等，在国民经济中占据不可替代的举足轻重的地位。本文简要概述了传统块状炭材料的国内外发展现状，在此基础上论述了我国相关领域中存在的问题，以期引起对传统但却十分重要的块状炭材料的进一步重视。     

The role of forest and bioenergy strategies in the global carbon cycle

Forest and bioenergy strategies offer the prospect of reduced CO₂ emissions to the atmosphere. Such strategies can affect the net flux of carbon to the atmosphere through 4 mechanisms: storage of C in the biosphere; storage of C in forest products; use of biofuels to displace fossil-fuel use; use of wood products which often displaces other products that require more fossil fuel for their production. We use the mathematical model GORCAM (Graz/Oak Ridge Carbon Accounting Model) to examine these mechanisms for 16 land-use scenarios. Over long time intervals the amount of C stored in the biosphere and in forest products reaches a steady state and continuing mitigation of C emissions depends on the extent to which fossil fuel use is displaced by the use of bioenergy and wood products. The relative effectiveness of alternative forest and bioenergy strategies and their impact on net C emissions strongly depend, for example, on the productivity of the site, its current usage, and the efficiency with which the harvest is used. When growth rates are high and harvest is used efficiently, the dominant opportunity for net reduction in C emissions is seen to be fossil-fuel displacement. At the growth rates and efficiencies of harvest utilization adopted in many of our base scenarios, the net C balance at the end of 100 years is very similar whether trees are harvested and used for energy and traditional forest products, or reforestation and forest protection strategies are implemented. The C balance on a plantation system that provides a constant output of biomass products can look different than the balance of a single parcel of land.     

ALGORITHMIC SYNTHESIS OF GENERAL NON-SHARP SIMPLE DISTILLATION COLUMN SEQUENCES

An algorithmic approach was used to select recoveries for non-sharp sequence designs. Simple distillation columns were employed. The non-key component distribution was modeled using the Fenske equation. The combination of producing impure products and allowing non-key component distribution, results in a large search space. With this large search space size and software limitations, five problems were solved (see summary table in the Design Examples sub-section). The optimal non-key component distribution was found to be significant but not necessarily maximal. Parallel processing was selected as optimal in contrast to the more traditional sequential processing.     

提高热轧带卷的成材率途径

莱钢1500mm热轧生产线于2005年6月投产。通过对轧钢生产过程中各环节的有效控制,使成材率显著提高,居于全国同行业领先水平,取得了良好的经济效益。     

石膏制品防水防潮剂的研制与开发

本文提出采用高分子有机材料配合，生产石膏制品防水防潮剂的生产方法和工艺。该剂还可以应用到氧化镁系列板材，同时提出开发珠光或彩色防水防潮剂，能达到满足的装饰效果，值提开发推广。