Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

Entry into force of the UN Watercourses Convention: why should it matter?

The United Nations Watercourses Convention entered into force on 17 August 2014, following a long and complex journey that dates back to 1970 when the UN referred the matter to its legal arm, the International Law Commission. This article follows the Convention through that long and turbulent road, examines its main provisions and analyses the reasons for the delay of its entry into force. It concludes by answering the question of why entry into force of the Convention should indeed matter.     

Quantitative risk assessment using a Japanese hydrogen refueling station model

Although hydrogen refueling stations (HRSs) are becoming widespread across Japan and are essential for the operation of fuel cell vehicles, they present potential hazards. A large number of accidents such as explosions or fires have been reported, rendering it necessary to conduct a number of qualitative and quantitative risk assessments for HRSs. Current safety codes and technical standards related to Japanese HRSs have been established based on the results of a qualitative risk assessment and quantitative effectiveness validation of safety measures over ten years ago. In the last decade, there has been much development in the technologies of the components or facilities used in domestic HRSs and much operational experience as well as knowledge to use hydrogen in HRSs safely have been gained through years of commercial operation. The purpose of the present study is to conduct a quantitative risk assessment (QRA) of the latest HRS model representing Japanese HRSs with the most current information and to identify the most significant scenarios that pose the greatest risks to the physical surroundings in the HRS model. The results of the QRA show that the risk contours of 10^?3 and 10^?4 per year were confined within the HRS boundaries, whereas the risk contours of 10^?5 and 10^?6 per year are still present outside the HRS. Comparing the breakdown of the individual risks (IRs) at the risk ranking points, we conclude that the risk of jet fire demonstrates the highest contribution to the risks at all of the risk ranking points and outside the station. To reduce these risks and confine the risk contour of 10^?6 per year within the HRS boundaries, it is necessary to consider risk mitigation measures for jet fires.     

苯乳酸抑制链格孢霉作用靶位的分析

以从自然腐败的樱桃上分离的链格孢霉（Alternaria sp.）LD3.0086为指示菌，研究苯乳酸对链格孢霉的主要抑制作用靶位。应用分光光度法测定苯乳酸对链格孢霉的最小抑菌浓度，通过卡尔科弗卢尔荧光增白剂染液（calcofluor white，CFW）染色观察苯乳酸对菌丝顶端生长的破坏作用，利用扫描电子显微镜和透射电子显微镜观察链格孢霉的超微结构变化，通过测定苯乳酸作用前后链格孢霉上清液中N-乙酰葡萄糖胺质量浓度变化研究苯乳酸对菌丝细胞壁的破坏作用，应用荧光双染色法观察苯乳酸对链格孢霉菌丝细胞膜的损伤作用。结果表明，12.5 mmol/L的苯乳酸能有效抑制链格孢霉的生长；与对照组（无菌水处理）相比，苯乳酸处理后链格孢霉顶端生长细胞无明显形变，经12.5 mmol/L苯乳酸处理的链格孢霉上清液中N-乙酰葡萄糖胺质量浓度基本不变；苯乳酸处理24 h，链格孢霉菌丝细胞壁表面无明显损伤，细胞内结构发生明显变化；苯乳酸短时间（4 h）处理链格孢霉，菌丝细胞膜仍较为完整，加入苯乳酸较长时间（8 h）后细胞膜发生破裂。综合分析可知，苯乳酸对链格孢霉的主要作用靶位应不是菌丝体的细胞壁和细胞膜，而是在菌丝体内部，通过破坏菌丝内部细胞器结构或引起细胞内的生化反应，从而抑制链格孢霉的生长和繁殖，发挥抑菌活性。     

Epos – an instrument for the assessment of the ethical position in software development

Digital technology becomes more powerful, intelligent, pervasive and ubiquitous. Ethical aspects of this development have not yet drawn the appropriate attention of researchers and engineers. This paper presents an instrument that aims at measuring the individual ethical position with regard to the design and development of computer software. The development of the Epos tool was based on two data collections. The data of the first survey (n₁ = 147 participants) were used to select items and to determine the factorial structure of the questionnaire. Results show that the Epos instrument reliably assesses peoples’ ethical opinion with respect to five central components: (1) regulation, (2) data privacy, (3) domain specific knowledge, (4) societal responsibility and (5) company responsibility. In the second survey, we determined the stability of the instruments factor structure by assessing a sample of n₂?=?196 participants. A confirmatory factor analysis (CFA) supported the initial factor structure. Next steps and further implications are discussed regarding the final version of the questionnaire.     

Catalytic supercritical water oxidation of tri-n-butyl phosphate: Process optimization by response surface methodology and cytotoxicity assessment

Catalytic supercritical water oxidation (SCWO) of an organophosphate flame retardant, namely tri-n-butyl phosphate (TNBP) was studied. Firstly, copper oxide nanoparticles (NPs) were synthesized in SCW and their properties were characterized by various analyses. Afterwards, their catalytic performance was investigated under different conditions including reaction temperature (400–500 °C), TNBP volume percentage in the feed (1–4%), oxidant ratio (0–2) and reaction time (50–150 min) based on response surface methodology (RSM). The synthesized CuO NPs had an average particle size of 30 nm with a narrow distribution. According to RSM analysis, the reaction temperature and time are the most significant factors; whereas, the impact of the other factors, especially TNBP volume percentage in the feed, was found to be negligible. Overall, excellent performance was achieved under optimal conditions found by the RSM, which was reaction temperature of 500 °C, TNBP volume percentage of 4%, oxidant ratio of 1.5, and reaction time of 90 min. The TOC removal efficiency as an indicator of TNBP degradation was about 99%. Finally, in vitro cell viability assays for the cytotoxicity evaluation of fresh and SCW-treated solution were applied. The results of MTT showed that SCWO converts TNBP into by-product that did not induce any cytotoxicity.     

Developing social impact assessment guidelines in a pre-existing policy context

Few jurisdictions have translated internationally agreed social impact assessment (SIA) principles into statutory provisions. Governments and regulatory bodies tend to provide developers with high-level frameworks, or require that social impacts be ‘considered’, without specifying how this is to be done. In Australia, this lack of clarity leaves all parties uncertain about requirements for SIA. The New South Wales (NSW) Government’s 2017 release of the SIA guideline for State-significant mining, petroleum and extractive industry development represents an attempt to clarify requirements and provide guidance. In this paper, we describe the process of bringing this guideline to fruition from the perspective of being directly involved in its development, and highlight the challenges involved in integrating leading-practice principles into the state’s pre-existing policy framework. While the guideline represents a significant advance in policy-based SIA guidance, some aspects leave room for improvement. The real test of the guideline’s impact will lie in its influence on SIA practice in NSW, and ultimately in social outcomes for communities affected by resources projects.     

Additive manufacturing of bipolar plates for hydrogen production in proton exchange membrane water electrolysis cells

Water electrolysis is a process that can produce hydrogen in a clean way when renewable energy sources are used. This allows managing large renewable surpluses and transferring this energy to other sectors, such as industry or transport. Among the electrolytic technologies to produce hydrogen, proton exchange membrane (PEM) electrolysis is a promising alternative. One of the main components of PEM electrolysis cells are the bipolar plates, which are machined with a series of flow distribution channels, largely responsible for their performance and durability. In this work, AISI 316L stainless steel bipolar plates have been built by additive manufacturing (AM), using laser powder bed fusion (PBF-L) technology. These bipolar plates were subjected to ex-situ corrosion tests and assembled in an electrolysis cell to evaluate the polarization curve. Furthermore, the obtained results were compared with bipolar plates manufactured by conventional machining processes (MEC). The obtained experimental results are very similar for both manufacturing methods. This demonstrates the viability of the PBF-L technology to produce metal bipolar plates for PEM electrolyzers and opens the possibilities to design new and more complex flow distribution channels and to test these designs in initial phases before scaling them to larger surfaces.     

Colostrum source and passive immunity transfer in dairy bull calves

Colostrum is essential for good neonate health; however, it is not known whether different calves absorb the nutrients from colostrum equally well. In this study, the absorption of protein, IgG, and γ-glutamyl transferase was compared in newborn dairy bull calves for 1 wk after feeding colostrum from different sources. Thirty-five Holstein-Friesian bull calves were randomly allocated into 3 groups and fed colostrum within 4 h after birth. Group A calves (n = 12) were bottle fed colostrum from their own dam for 3 d. Colostrum from these group A cows was also used as foster cow colostrum for the group B calves (n = 12), such that each group A and B calf pair received identical colostrum from each milking of the respective group A dam (10% of birth weight per day). The group C calves (n = 11) were fed 1 bottle (2 L) of pooled colostrum and transition milk (referred to as pooled colostrum), as was the standard practice on the dairy farm. The pooled colostrum was collected from the other dairy cows on the farm 0 to 4 d postpartum and stored at 4°C for less than 12 h. Blood was sampled from calves before the first feeding and at 1, 2, 3, and 7 d after birth. Levels of total solids, total protein, and IgG were higher in the dam colostrum than in the pooled colostrum. At birth, there were no differences between the calf groups for any measurements, and all calves had very low IgG levels. After receiving colostrum, the glucose, plasma γ-glutamyl transferase, serum total protein, and IgG concentrations increased significantly in all calves. There were no differences in any blood measurements at any time point between the pairs of group A and group B calves that received colostrum from the same cow except for the IgG concentration 2 d after birth. However, the group A calves had a higher total serum protein level and IgG concentration than the group C calves for all the time points after the first feeding. The group B calves had a higher IgG concentration than the group C calves on d 1, 2, and 7 after birth. Compared with groups A and B, there was no difference in the proportion of calves in group C that failed to have passive immunity transferred adequately based on the IgG threshold (<10 g/L). Thus, the calves receiving identical colostrum from the same cow had the same levels of IgG, and even the pooled colostrum provided sufficient transfer of IgG as the calves were fed within 4 h after birth.