焦化厂门型吊改造

从门型吊承轨梁的受力分析入手．研究剖析了原结构产生裂纹的诸多原因．通过理论计算。做出了承轨梁与桁架连接接点的最佳设计．提出了符合现场实际情况的更换承轨梁的最佳方案，为类似设备改造提供了可借鉴的经验。     

方波扫描路径确定声源声功率误差特性分析

改进了矩形测量面方波扫描路径测量声功率的误差模型 ,以单极子、偶极子及四极子声源为例 ,给出了扫描方向、测量面离声源的距离及扫描线的密度的选取对理论误差的分布图形。分析结果表明 :对选定的测量面 ,在扫描线密度小的情况下 ,通过调整声源离测量面的距离 ,可以在声源近处找到一个最优点或较优点 ,使理论误差为零或很小 ;在绝大多数情况下 ,沿测量面长边扫描误差比沿短边扫描小。     

新型非蒸散消气剂的激活温度和吸气性能的实验研究

对主要成分为Zr和Co的新型非蒸散消气剂进行了活化温度及吸气性能的实验研究。实验表明其活化温度为200—250℃，对N2，H2等活性气体有很好的抽速，对惰性气体He等无抽速。     

长江口北支水道水沙特性分析

从实测资料出发,结合水流数值计算成果,对长江口北支水道的水流、泥沙和含盐度等资料进行分析,得出了北支水道的水沙特性,并分析了水沙变化与河床变化的相互关系.北支水道在1958年南通河段河势控制后,径流分流比逐年下降,并渐趋稳定于3%左右.北支水道受径流影响越来越小,主要受潮流作用.随着水沙特性的逐年变化,北支水道0 m以下槽蓄容量逐年减小,并渐趋稳定,北支上段为逐年淤积最快的区域.由此反过来影响了水沙条件的进一步变化,使北支上段平均潮差增加,北支的会潮点由崇头附近下移至青龙港附近.     

Thickness-dependence of stoichiometry and microstructure characteristics in correlation with conductivity type of CdTe films

CdTe films were prepared by physical vapour deposition on a substrate at room temperature (RT) as well as on a cold (LT) one using low deposition rate. The thickness-dependence of stoichiometry revealed an abrupt decrease in the Cd/Te ratio as the thickness increases. Change of thickness did not affect the type of observed (111) crystallographic texture, only the degree of preferred orientation is enhanced as the film grows. The internal strain was negligible while the crystallite size increased rapidly at small thickness (up to 400 nm), and less thickness dependence was observed with further film growth. However, thickness dependence of lattice parameters showed a minimum and a maximum at approximately 300 nm in the case of RT and LT, respectively. The observed change in conductivity from n- to p-type and its vital correlation with the stoichiometry and structural characteristics were presented. Based on thickness dependence of stoichiometry and lattice parameters as well as the conductivity type, formation and annihilation of lattice defects were considered.     

Numerical simulation of slider dynamics during slider–disk contact

In this paper, the dynamic behavior of pico slider in contact with the disk was calculated. The analysis model consists of a simplified suspension model, an air bearing model, and a slider–disk contact model. The contact model consists of two elements. One is surface roughness model measured by Atomic Force Microscope (AFM) and the other is micro-waviness model. The dynamic behaviors of the tri-pad slider are calculated at several rotation speeds to investigate slider vibration modes during slider–disk contact. The slider oscillation frequency depends on the rotation speed and it saturates about twice as much as eigen frequency of air bearing pitch mode.     

多级复合布尔函数性能研究

本文研究了加法复合布尔函数和乘法复合布尔函数,在平衡性、k次项系数、K次扩散准则(PC)、相关免疫 性(CI)、Walsh谱、代数次数、小项分布等方面得到了一批新结果。     

MLS结构的电容-电压特性

本文报导在 Si 衬底上拉制聚酰胺 LB 膜的电容-电压特性,结果表明:它具有与其它绝缘膜相似的特性,为聚酰胺 LB 膜应用于场效应器件奠定了基础。     

用激光测振仪测量扬声器纸盆的振动特性

用激光外差测振装置测量了扬声器纸盆振动幅度与激励电压及激励频牢之间的关系。为扬声器结构及振动特性的研究提供了一种精度高、重复性好的可靠测量方法。     

基于小波包和包络分析的滚动轴承故障自动诊断方法

提出了一种基于峭度-小波包-包络分析的滚动轴承故障自动诊断方法。首先用峭度系数判断是否出现故障,再针对故障轴承振动信号非平稳和调幅的特点,用小波包将信号分解到不同的节点上。然后将不同节点的重构信号做包络谱分析,将谱峰处的频率同滚动轴承内圈、外圈、滚珠、保持架等的故障频率进行对比分析,在此基础上,运用最小距离判别法则自动获得故障原因,从而实现滚动轴承故障的自动诊断。通过对实验中采集到的轴承振动信号进行分析,证明了该方法在轴承早期故障诊断中的有效性。