Electrochemical C-V Characteristics and Photoluminescence of a-C∶N Films

Amorphous carbon (a-C) films and amorphous carbon films incorporating with the nitrogen (a-C∶N) were deposited on silicon substrates in a radio-frequency driven plasma enhanced chemical vapour deposition system, while the surface electrical properties of films were investigated by electrochemical capacitance-voltage measurements. It was examined the effect of the interface defects on the properties and deduced that the conducting type of a-C∶N films was n-type. Subsequently, a comparative studies of a-C and a-C∶N films were performed by photoluminescence spectra depending on the temperature. With the decrease of the temperature, the main band with peak energy of 2.48 eV in the a-C∶N films was more intense compared with the other three bands caused by amorphous C in the a-C films.     

The enhanced coercivity for the magnetite/silica nanocomposite at room temperature

Magnetite/silica nanocomposite was synthesized by a facile solvothermal processing at 150 °C for about 10 h. X-ray diffraction (XRD) analysis revealed the effect of annealing on the crystallinity of silica. Transmission electron microscopy (TEM) images showed the good dispersion of magnetite in the silica matrix. Magnetic properties of the nanocomposite were characterized by vibration sample magnetometer (VSM), and the enhanced coercivity was explained by the intrinsic anisotropy of the particles enhanced by the interparticle dipolar fields.     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

静态EPS及其在建筑工程中的应用

一级负荷中特别重要的负荷，除由两个电源供电外，尚应增设应急电源。在供电条件比较差的地区，取得第二个电源供给一级负荷有困难时，也需要增设应急备用电源。以往经常用自备柴油发电机组、蓄电池、干电池和镍锦电池应急灯作为应急备用电源。本文通过对目前常用的各种应急电源的分析比较，推荐一种新颖的、静态、无公害、免维护无人值守的、供电质量好、安全可靠的集中供电式EPS装置。     

Capture of Airborne Particulate Using Surface Applied Emulsions: Potential for Postdetonation Dirty Bomb Cleanup

Recent research has proposed the use of asphalt and tall-oil-pitch emulsions for stabilizing radioactive contamination deposited on surfaces in urban areas. The objective of this project was to investigate whether surface applied emulsions could capture airborne radioactive particulate. Laboratory experiments included wind-blown particulate capture studies using an acrylic column and particulate retainment experiments using a wind box capable of producing wind speeds of 96?km/h. A probe methodology was developed to relate particulate retainment to a tack force on the emulsion surface. Experiments were also performed to determine the potential for such emulsions to absorb particulate matter into their emulsion matrix. Tall-oil-pitch emulsions outperformed asphalt emulsions in terms of particulate retention, tack force, and the ability to absorb magnesium silicate. Both tall-oil-pitch and asphalt emulsions were capable of extracting 22–24?g?m?2 of powder from particulate-laden airflow. Tall-oil-pitch emulsions were capable of retaining as much as 5–10% of magnesium silicate powder applied (i.e., retainment densities of 10–20?g?m?2) even after seven?days of curing and after applying 96.5?km/h (60?mph) wind. Tall-oil-pitch emulsions were able to absorb surface-applied magnesium silicate (approximately 0.1–0.2?g of magnesium silicate per 1.0?g of emulsion within three?days) into their emulsion matrix, preventing the magnesium silicate from being exposed to the external environment. Initial results with these five different emulsion formulations suggested particulate capture was feasible. Future emulsion formulations (i.e., longer curing times with greater acid concentrations) should be tested to optimize this postdetonation response strategy.     

Two-Dimensional Physical and Numerical Modeling of a Pile-Supported Earth Platform over Soft Soil

This paper focuses on the mechanisms occurring in a granular earth platform over soft ground improved by rigid piles. Two-dimensional physical model experiments were performed using the Schneebeli’s analogical soil to investigate the load transfer mechanisms by arching and the settlement reduction and homogenization. Experimental outputs are compared to results obtained on a numerical model using a plane strain continuum approach. The impact of the constitutive model complexity to simulate the platform material behavior was first assessed, but no large difference was recorded. As far as the proposed model, which takes the main features of the observed behavior satisfactorily into account, the numerical procedure could be validated and the parametric studies extended numerically. Both approaches of this study underlined the main geometrical and geotechnical parameters which should inevitably be taken into account in a simplified design method, namely the capping ratio, the platform height, and the platform material shear strength.     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

热处理对Ti-25V-15Cr-2Al-2Mo-0.2C合金组织稳定性的影响

研究了热处理对Ti-25V-15Cr-2A1-2Mo-0.2C阻燃β钛合金组织稳定性的影响。结果表明，高温固溶并直接时效处理导致合金β基体上析出较多的α相沉淀，尤其在随后的热暴露组织中形成了恶化合金塑性的连续晶界α膜。然而，若在时效前再进行一次低温固溶处理则可明显减少α相的析出数量，合金的热稳定性因此而得到显著改善。