含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

常减压装置设备腐蚀分析及防护措施

文章介绍了中国石油化工股份有限公司齐鲁石化分公司胜利炼油厂第二常减压蒸馏装置的总体情况,分析总结了装置在2000-2005年期间停工闲置及开工运行过程中设备腐蚀情况和防护中所做的工作,可供相似类型、相似状态的装置借鉴。     

X80焊管H_2S环境应力腐蚀开裂行为研究

采用三点弯曲加载法和微电极扫描测试技术,研究了X80高强度级管线钢及其焊缝区的抗H2S环境应力腐蚀开裂(SSCC)行为。测定了焊接接头的显微硬度分布,分析了显微组织结构、力学性能及抗腐蚀性能之间的相关性。研究表明,热影响区(HAZ)对应力腐蚀开裂最为敏感,母材的纵向和横向取样对应力腐蚀敏感性影响不显著,薄壁管材比厚壁管材有较好的抗H2S环境应力腐蚀性能。HAZ晶粒粗大、硬度高,局部腐蚀倾向大,由此导致该区SSCC敏感性高。     

多功能杀菌剂的合成及其性能研究

在现有季铵盐类杀菌灭藻剂上增加一个脂键，连接一个有机酸基团，合成一种兼具阻垢缓蚀功能的新型工业水处理用杀菌灭藻剂(多功能杀菌剂)，经一系列评价实验表明：新型杀菌剂是较理想的杀菌剂，在较低浓度下，对硫酸盐还原菌(SRB)及腐生菌(TGB)均有很好的杀灭效果，优于1227杀菌剂，同时还具有较好的缓蚀阻垢效果。     

模糊层次分析法在腐蚀影响因素分析中的应用

结合国内外对碳钢CO2腐蚀影响因素的研究成果,采用模糊层次分析法对影响输油管道 CO2腐蚀的因素进行定量分析,明确界定出这些因素对二氧化碳腐蚀影响的相对重要性(权重),为后续制定经济有效的管道内腐蚀防护措施提供了客观依据。     

魏氏组织对20#碳钢H2S应力腐蚀开裂性能的影响

文章对H₂S-CO₂-H₂O腐蚀环境下发生H₂S应力腐蚀的20^＃碳钢弯管（无缝钢管）进行了成分、组织、拉伸、硬度和应力腐蚀开裂等性能的试验研究，并与同材质、同时投产、腐蚀环境基本相似而未发生应力腐蚀开裂的在役弯管及未使用的新弯管作对比，结果表明魏氏组织是引起20^＃钢发生应力腐蚀开裂的主要原因；正火能消除魏氏组织，降低钢的应力腐蚀开裂敏感性。     

N-油酰基肌氨酸钠对除盐水缓蚀性能的探讨

对N-油酰基肌氨酸钠单体的缓蚀性能以及与常用除盐水缓蚀剂的协同作用作了探讨,发现在一定浓度下,单体对经过加氨调节后的高温除盐水(氨后除盐水)有良好的缓蚀作用,且与大多数除盐水缓蚀剂有良好的协同效应。在此基础上研制了一种复合药剂,并对其缓蚀、阻蚀性能作了研究。动电位极化曲线扫描图谱表明,该复合药剂属于抑制阳极腐蚀的阳极型缓蚀剂,其适用的水质条件为[Cl~-+SO_4~(2-)]不超过50 mg／L,pH不低于8.0；与阻垢剂复配,可以适用于含Ca~(2+)不超过45 mg／L的水质条件。     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

泡沫夹克管的防水与保温

针对辽河油田应用泡沫夹克管道的情况，从泡沫夹克管的制作和敷设施工直到设计等环节，结合泡沫夹克管防腐保温的机理，并从理论与实践相结合角度出发，提出导致泡沫夹克管腐蚀损坏的最主要原因是管道保温层漏水，进而提出了在设计和施工过程中提高泡沫夹克管质量的措施。     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.