Law,liability and expert systems

This paper examines some of the possible legal implications of the production, marketing and use of expert systems. The relevance of a legally useful definition of expert systems, comprising systems designed for use both by laymen and professionals, is related to the distinctions inherent in the legal doctrine underlying provision of goods and provision of services. The liability of the sellers and users of, and contributors to, expert systems are examined in terms of professional malpractice as well as product liability. A recurring theme indicates that legislators may be inclined to restrict possibilities of liability suits in order to avoid disincentives to the creation of expert systems.     

莱钢职业安全健康动态监控信息系统的建立及运行分析

以网络技术和信息技术为依托，建立职业安全健康动态监控信息系统，进行职业安全健康管理的监控和预警，提高安全管理的现代化水平。     

热轧带肋钢筋屈服不明显原因分析与探讨

针对涟钢热轧带肋钢筋的屈服不明显现象，从金属的金相组织、人工时效、自然时效、测试方法等方面着手，寻求各因素对钢筋力学性能的影响，并阐述了该异常组织的形成机理及相关因素，指出魏氏体、粒状贝氏体等的存在是造成带肋钢筋性能异常的主要原因，同时对部分屈服不明显的带肋钢筋判定提供了较为科学的依据。     

Identification of gaps in mangrove forests with airborne LIDAR

Mangrove forests change frequently due to disturbances from tropical storms, frost, lightning, and insects. It has been suggested that the death and regeneration of trees in small gaps due to lightning may play a critical role in mangrove forest turnover; however, the large-scale quantification of spatial pattern and areas of gaps is lacking for investigating this issue. Airborne light detection and ranging (LIDAR) technology provides an effective way for identifying gaps by remotely obtaining direct measurements of ground and canopy elevations. A method based on an alternative sequential filter and black top-hat mathematical morphological transformation was developed to extract gap features. Comparison of identified gap polygons with raw LIDAR measurements and field surveys shows that the proposed method successfully extracted gap features in mangrove forests in Everglades National Park. There are 400–500 lightning gaps per square kilometer in mangrove forests at the study sites. The distribution of gap sizes follows an exponential form and the area of gaps with sizes larger than 100 m² account for 55–61% of the total area of gaps. The area of gaps in the mangrove forest in Everglades National Park is about 4–5% of the total forest area and the average gap formation rate is about 0.3% of the total forest area per year, indicating that lightning gaps play an important role in mangrove forest dynamics.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

水浴法加温液氧泵

1　故障现象一次 ,我们用KL -1 5型制氧制氮车开机制氮 ,给一只容积为 40升、最高工作压力为1 4 7MPa的气瓶灌充氮气 ,当气瓶充气压力升高到一定值时不再上升。反复开泵 ,压力基本不变。液氧泵停止时 ,出口压力无明显下降。经分析判断导致气瓶压力升高到一定值时不再上升的原因是由于液氧泵被冻结所致。2　排除方法首先关闭液氧泵。拧开制冷机氢气放气阀 ,使压力下降到 1 0MPa。开大放气阀 ,使二级压力保持在 0 3 5MPa左右。调整正流空气调节阀 ,调节好中部温度。关闭液氮进液氧泵阀和气氮出液氧泵阀。戴棉布手套 ,拆开液氮进口接头、…     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

高炉冷却壁失效原因研究

本文针对安钢高炉冷却壁破损的形式、原因进行研究分析,探讨了冷却壁的结构、材质、加工与安装工艺对其寿命的影响。介绍了安钢高炉炉役后期冷却壁的维护生产实践。     

Hybrid LES — Review and assessment

In the late eighties and up to the beginning of nineties computation of turbulent flows is mostly dominated by RANS (Reynolds Averaged Navier-Stokes Simulation) type modelling. During the last few years URANS (Unsteady RANS) and LES (Large Eddy Simulation) type of approaches have been attempted with some success. Yet, there have been many difficulties when LES is applied to practical engineering problems and to high Reynolds number flows as energy dissipating eddies become really small and mesh resolution required for a reasonably resolved LES approaches that of DNS (Direct Numerical Simulation). An alternative solution suggested was to combine RANS and LES, which in general referred to as Hybrid LES. There have been many proposals for combining RANS and LES in different ways. In this article, some of the issues involved in performing hybrid LES reported in the recent literature is briefly reviewed.     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。