显像（示）管阴极像黑洞状缺陷形成的原因及消除对策

本文通过有关理论依据和试验数据，着重阐述了在显像（示）管测试中，阴极像中心黑洞状缺陷产生的原因以及消除这种缺陷的处理方法。通过这种处理方法处理过的显像（示）管，其整体质量水平（尤其是真空度）将会得到明显的提高。     

稀布阵综合脉冲孔径雷达旁瓣对消性能分析

定量分析了阵列孔径、干扰信号带宽、通道幅相误差以及Ａ／Ｄ变换器的量化噪声对大型稀布圆形阵列天线干扰对消效果的影响，介绍了稀布阵综合脉冲孔径雷达（ＳＩＡＲ）采用抽头延迟线以提高干扰对消性能的方法，并给出了数值计算与计算机模拟结果。     

日产1205t/h锅炉低温过热器爆管原因分析与技术措施

对河津电厂日产1 205 t/h锅炉低温过热器爆管原因进行了分析,指出对尾部竖井设置均流板的∏型布置锅炉,当靠近两侧墙的管屏出现个管偏离管屏时,容易导致偏离管磨损爆破,进而影响相邻管段.其事故和处理措施对同类型锅炉有借鉴作用.     

不锈钢管子管板自动钨极氩弧焊的试验研究

本文介绍了不锈钢管子管板焊的工艺试验情况,包括试验的内容和为保证焊接质量所采用的工艺参数和操作要点.     

高效“E”管的研究与应用

分析研究了机械加工表面多孔管(“E”管)的结构特点与性能,阐述了影响“E”管传热性能的因素,提出了有别于常规低肋管蒸发器结构设计与操作的建议。介绍了“E”管的应用情况,表明其适用于制冷机组的满液式蒸发器。     

导流管喷动床流体动力特性的实验研究

对以小米为物料的常规喷动床及导流管喷动床全床压降随表观气速变化规律进行了实验研究．结果表明，与常规喷动床相比，导流管喷动床不仅最小喷动速度、操作压降和最大压降均大幅减小，而且夹带高度较小时会在达到稳定喷动之前发生有利于操作的不稳定喷动现象．此外，导流管喷动床的流体动力特性受料床高度影响不大，但受导流管内径和夹带高度的影响显著．最后，依据实验结果提出了导流管喷动床最小喷动速度的关联式．     

Heat transfer augmentation in 3D internally finned and microfinned helical tube

Experiments are performed to investigate the single-phase flow and flow-boiling heat transfer augmentation in 3D internally finned and micro-finned helical tubes. The tests for single-phase flow heat transfer augmentation are carried out in helical tubes with a curvature of 0.0663 and a length of 1.15 m, and the examined range of the Reynolds number varies from 1000 to 8500. Within the applied range of Reynolds number, compared with the smooth helical tube, the average heat transfer augmentation ratio for the two finned tubes is 71% and 103%, but associated with a flow resistance increase of 90% and 140%, respectively. A higher fin height gives a higher heat transfer rate and a larger friction flow resistance. The tests for flow-boiling heat transfer are carried out in 3D internally micro-finned helical tube with a curvature of 0.0605 and a length of 0.668 m. Compared with that in the smooth helical tube, the boiling heat transfer coefficient in the 3D internally micro-finned helical tube is increased by 40-120% under varied mass flow rate and wall heat flux conditions, meanwhile, the flow resistance is increased by 18-119%, respectively.     

Thermoacoustic streaming in a tube with isothermal outer surface

Thermoacoustic oscillations at a cycle-steady state in a tube with an isothermal outer wall, and with one end closed and the other end connected to a wave generator, is analyzed based on a linearized theory. From the global mass conservation, an analytical solution has been obtained for the cross-sectional and cycle averaged axial velocity. It is shown that this averaged velocity is non-vanishing due to the mass streaming effect. By analyzing the global momentum balance, it is found that the cycle-averaged pressure depends on the momentum streaming and friction force, and a conservation relationship exists between the momentum streaming and the cycle-averaged pressure for the flow oscillating at a high frequency in a wide tube. An investigation of the global energy balance leads to an expression for thermoacoustic energy streaming. Furthermore, it is shown that the refrigeration effect is mainly caused by the non-vanishing mean velocity, and therefore the mass streaming and the energy streaming are intimately connected.     

超临界压力锅炉水冷壁倾斜并联内螺纹管内两相流不稳定性的试验研究

针对国产首台600 MW超临界机组在亚临界压力条件下的水动力特性,进行了倾斜并联内螺纹管内的汽液两相流不稳定性试验研究,观察到压力降型和密度波型两种类型的脉动。探讨了影响不稳定性的主要参数。并给出了发生不稳定性的阈值。试验表明:在超临界锅炉滑压运行设计参数条件下,水冷壁管内不会发生两相流不稳定性。图11表1参7     

纳雍锅炉联箱管座孔加工刀具的设计

针对纳雍W火焰锅炉联箱的特点 ,结合生产中的实际情况 ,介绍了其管座孔加工刀具的设计方法