Mechanical properties and crosslink density of rare earth‐modified high‐abrasion furnace‐filled powdered natural rubber

High‐abrasion furnace‐filled powdered natural rubber [P(NR/HAF)] has more advantages than traditional HAF‐filled bale NR (NR/HAF) because of its better environmental performance and easier processing quality, but its lower mechanical properties are disadvantageous. To improve the mechanical properties, rare earth‐modified HAF‐filled powdered NR [P(NR/HAF‐Ln)] (Ln = Sm,La,Pr) was prepared by means of coacervation–coprecipitation, using rare earth‐modified HAF as separant and filler. The effect on mechanical properties of P(NR/HAF‐Ln) vulcanizate exerted by the emulsifier/HAF ratio, powdering temperature, Ln/HAF ratio and type of Ln, and HAF content were studied. The results indicated that when optimum formulation, the mechanical properties of P(NR/HAF‐Ln) vulcanizate were better than P(NR/HAF) vulcanizate. In addition, the relationship of the apparent crosslink density and HAF content of P(NR/HAF‐Ln), P(NR/HAF), NR/HAF vulcanizates was also investigated, along with their SEM microphotographs of tensile fracture surface, which indicated that the excellent mechanical properties of P(NR/HAF‐Ln) vulcanizate was attributed to correct amount of Ln that could increase crosslink density and reinforce the interface structure of NR matrix/HAF‐Ln particle. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1755–1762, 2006     

吸附回收氯乙烯精馏尾气中高浓度氯乙烯新工艺

用活性炭纤维作吸附剂，吸附并回收氯乙烯精馏尾气中的氯乙烯。与传统的工艺相比，具有流程短、吸附回收效率高、运行稳定、自动化程度高、安全性能好、投资和运行费用低等优点。在天津大沽化工有限责任公司的实际运行表明，氯乙烯的回收率稳定在90％以上，收到了很好的经济效益和环境效益。     

有机硅改性丙烯酸乳液性能的研究

采用含乙烯基官能团的有机硅单体与甲基丙烯酸酯、丙烯酸酯和丙烯酸羟基酯等单体通过种子乳液聚合方法进行共聚,合成了有机硅改性丙烯酸酯共聚乳液,考察了有机硅单体用量对乳液机械稳定性、热稳定性、电解质稳定性和冻融稳定性的影响,同时还考察了乳液胶膜的机械性能和吸水率改进。     

Supported Vanadia Catalysts for Dehydrogenation of Ethylbenzene with CO2

Alumina supported vanadia catalysts (V/Al) for selective oxidehydrogenation of ethylbenzene with CO₂ were prepared by impregnation method. During preparation the effect of promoters and calcined temperature was investigated, it was found these two items had a strong influence on the activity of V/Al catalysts. Dehydrogenation reaction with CO₂ was happened in the fixed-bed reactor at 450 °C. Results showed that 15.2% ethylbenzene conversion and 99.2% styrene selectivity were acquired when V₂K/Al catalyst was used.     

Physical agglomeration behavior in preparation of cellulose‐N‐methyl morpholine N‐oxide hydrate solutions by simple mixing

The different melting temperatures of N‐methyl morpholine N‐oxide (NMMO) hydrates in the cellulose–NMMO hydrate solution may be explained by the rather different crystal structures of NMMO hydrates, which are determined by the amount of the hydrates. The preparative process of cellulose–NMMO hydrate solution may result in cellulose structural change from cellulose I to cellulose II, depending on the amount of the hydrate. Mixtures of cellulose and NMMO hydrate in a blender was changed from the granules to slurry with increasing mixing time at 60–70°C, which is below the melting point of the NMMO hydrate. In the case of 15 wt % cellulose–NMMO hydrate granules, which were made by mixing for 20 min, the melting points of various NMMO hydrates were obtained as 77.8°C (n = 0.83), 70.2°C (n = 0.97), and 69.7°C (n = 1.23), respectively, depending on the hydrate number. However, the melting points of cellulose–NMMO hydrate slurry and solution were shifted lower than those of cellulose granules, while the mixing time of slurry and solution are 25 and 35 min, respectively. These melting behaviors indicate instantaneous liquefaction of the NMMO hydrate and the diffusion of the NMMO hydrate into cellulose during mixing in a blender. When cellulose was completely dissolved in NMMO hydrate, the crystal structure of cellulose showed only cellulose II structure. In the cellulose–NMMO products of granules or slurry obtained by high‐speed mixing, which is a new preparation method, they still retained the original cellulose I structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1687–1697, 2004     

一次性使用无菌注射器用橡胶活塞的化学分析方法的改进

介绍一次性使用无菌注射器用橡胶塞的化学分析方法。在适宜的酸度条件下，用碘量法测定易氧化物；重金属含量通常是测其硫化物的含量来判定的，本方法是采用硫代乙酰胶试剂作沉淀剂；锌离子能与亚铁氰化钾溶液及应生成白色络合物沉淀，因此采用亚铁氰化钾比浊法测其锌含量；利用硫氰酸铵比色法测其铁含量。本方法操作具体，比色明显、定量明确，对试样的测定得到了满意的结果。     

Concentration of tocopherols from soybean sludge by supercritical carbon dioxide

A supercritical fluid extraction method has been applied to test the feasibility of tocopherol concentration from soybean sludge with carbon dioxide at temperatures and pressures ranging from 35 to 70°C and 200 to 400 bar, respectively. The supercritical solubility of the esterified soybean sludge was over 4–6 times greater than that of the original soybean sludge. By a simple batch-type one-stage method the tocopherols in the esterified soybean sludge could be concentrated up to 40 wt%. The overall results of the present study show that soybean sludge initially containing about 13–14 wt% tocopherols may require a countercurrent multistage column to be highly and effectively concentrated.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

Chemical reactivity of CO and CO2 at a Cu(110)-Cs surface

Carbon dioxide and carbon monoxide undergo reactive chemisorption with cesium modified Cu(110) and Cu(110)-O surfaces and via the anionic intermediate CO ₂ ^– (a) form a surface carbonate. The CO ₂ ^– (a) species was characterised by VEELS and XPS at low temperature (80 K) and the surface carbonate at 295 K. For cesium modified Cu(110) surfaces chemisorption of carbon monoxide gives rise to electron energy loss peaks (v _co) as low as 1450 cm^–1 at 295 K.     

Catalytic aerobic oxidation of ethylbenzene over Co/SBA-15

Co(II)O was highly dispersed in the mesopores of SBA-15 by alcoholic impregnation method and characterized by XRD, TEM, UV–VIS DRS, TPR, and XRF techniques. It was found that tetrahedral coordinated Co(II)O was stabilized by SBA-15 at low Co-loading. Co/SBA-15 showed much higher activity than Co(OAc)₂ or Co₃O₄ in the liquid-phase aerobic oxidation of ethylbenzene under solvent-free condition.