常门铺水库溢洪道设计方案比较

在常门铺水库溢洪道改造中，通过不工模型试验，对其数据成果进行分析并进行方案比较，最终采用即经济又合理的方案二，为国家节省投资50.8万元。     

龙滩工程按正常蓄水位400m方案一次建成效益巨大

2003年11月龙滩工程将实现大江截流，随着工程建设的全面推进，越发显出实施龙滩水电站正常蓄水位400m一次建成方案的重要性和紧迫性。相对分期建设而言，400m水位一次建成，工程效益大、增加投资少、无后期加高过程中的各种技术难题，基本不影响电站的初期发电效益，水轮机设计与运行问题少、机组运行条件好，电站规模效益与社会综合效益巨大，有利于移民安置和库区经济的发展，对国家、地方、企业均十分有利，因此应尽快决策实施400m一次建成方案。     

用欢喜岭油田低凝稠油生产AH-90重交通道路沥青

针对欢喜岭油田低微稠油的特点，采用常压蒸馏—氧化沥青联合装五的工艺流程，生产出AH-90重交通道路沥青。经测试表明，各项性能均达到我国现行重主通道路沥青技术指标。在高温稳定性、低温抗裂性等方面都优于新加坡壳牌沥青。是一种优质的道路沥青。     

柴油机针阀体的乙炔低压渗碳

乙炔低压渗碳可以有效地避免在真空渗碳过程中产生炭黑和焦油，同时由于乙炔具有较高的供碳能力，使这一技术尤其适用于针阀体这样的小直径深盲孔零件。     

Biogas and biomass technology: Energy generation from biomass and waste in the Netherlands

Within the European Community, the interest in energy generation from biomass and waste is increasing. A brief overview is given of several thermal conversion technologies, of biomass production and waste availability in the Netherlands. Based on this, the possibilities for energy generation from biomass and waste in the Netherlands are evaluated.     

The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

反水锤的危害及防止

反水锤是发生在反击式水轮机尾水道中的一种特殊水锤现象，其压力峰值可达正常压力的几倍，甚至十多倍，以致造成肢解转轮、折断导叶、破坏顶盖、抬起转子的严重事故。因此，研究反水锤发生的原因，从而提出防止反水锤事故的措施尤为重要。     

3D圆阀塔板性能研究

介绍了3D圆阀塔板的结构特点和实验研究情况。以空气和水为工质进行了冷模实验,研究了3D圆阀塔板的塔板压降、雾沫夹带量和泄漏量等流体力学性能。利用氧解吸法测定其塔板效率,并在相同条件下与F1浮阀塔板进行了对比实验。结果表明,在相同条件下,3D圆阀塔板比传统F1浮阀塔板的塔板效率提高5%~15%,塔板压降约低100 Pa,泄漏量和雾沫夹带量与F1浮阀塔板基本相当,是一种综合性能优良的新型浮阀塔板。     

修井机多桥间转向传动机构的设计

对于大型修井机采用的重型底盘,多桥转向系统是底盘开发中的关键技术之一。在分析目前修井机采用的转向传动结构(方案1)存在问题的基础上,参照军用车底盘的应用案例又提出了2种方案,经对比分析,确定了最佳的传动机构新方案,并根据多桥转向理论和四连杆机构的几何关系对该机构进行了参数确定。通过实际应用,证明该转向传动布置方案具有传动误差小、不产生附加转向、现场调节安装方便、易于组织生产等特点。