The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

非协调h－p型有限元补偿法

详细讨论了非协调ｈ－ｐ型有限元的补偿法，给出了令人满意的收敛阶．     

Detection and analysis of transition from annular to intermittent flow in vertical tubes

In vertical co-current gas-liquid flow, the transition from annular to intermittent flow occurs when gas core becomes interrupted by liquid bridges due to the instability of the interfacial capillary waves. An analytical model is formulated to explain the liquid bridging in terms of the growth of finite amplitude interfacial capillary waves. Experimental results show that the longest wave length, which is associated with the transition, is about eight times the wave length of waves moving with the velocity of the liquid film.     

Simulation of leachate migration in leaky aquifers

A two-dimensional cross-section finite difference model is presented to simulate density dependent leachate migration in leaky aquifers. Unlike existing models, a new approach is adopted to couple the groundwater-flow equation and the hydrodynamic dispersion equation with the elimination of the intermediate step of calculating velocities. The concept of the reference density is employed, permitting increased accuracy (over pressure-based models) in the representation of the transport process. The model is then used to study the effect of several hydraulic and transport parameters on the flow pattern and plume migration which are found to be very sensitive to most of these parameters. Equiconcentration and equipotential lines are overlapped to provide a better understanding of the coupling effect.     

液压胀形轧辊油槽深度的确定

对液压胀形轧辊（即国外的ＶＣ轧辊）辊套热装后的弹性变形进行了有限元分析，给出了确定油槽最小深度的计算公式。本文的有限元计算结果与实验结果吻合，某些结论可为液压胀形轧辊的结构设计提供理论依据。     

关于Imamura猜想1的一个结果

本文证明了GF(q)的特征为2且n为奇数时GF(q~n)在GF(q)上有自对偶正规基。     

分析恒载效应的有限元方法

本文在Takabatake关于恒载对梁静、动力影响的研究工作的基础上,导出了梁考虑恒载效应的动力分析有限元公式,提出了荷载影响刚度矩阵的概念。分析了分布和集中两种恒载型式对简支梁和悬臂梁自振特性的影响。计算结果表明,用本文方法与Takabatake应用Galerkin方法和近似闭合解方法的结果吻合良好。同时由于本文采用了矩阵形式,不仅便于编制计算机程序,且使方法有更广泛的适用性和灵活性,可更方便地用于各种不同的构造和边界条件下的实际结构。     

双迭片弯曲压电陶瓷换能器及振动模态分析测量

介绍了双迭片弯曲压电陶瓷换能器的制作及边缘固定金属压电陶瓷双迭片弯曲振动，并利用有限元分析了换能器的谐振模式，采用激光多普勒干涉仪对换能器的谐振特性以及振动速度和位移分布进行了测量和分析，结果表明：换能器空载性能良好，通过有限元分析与先进测量手段的结合，能够对换能器器件的制作与分析进行指导。     

基于Ansys的电化学加工辅助阴极设计

根据电化学加工极间间隙电势分布的拉普拉斯方程，提出了一种阴极设计算法－误差调整法。该算法的实现主要采用了Ansys有限元计算软件。计算结果表明：该法计算迭代次数较为适当，对于精度要求不高的电化学加工阴极设计，基于Ansys的辅助阴极设计有效可行。     

Dynamic analysis and drilling degrees of freedom

Finite element methods for dynamic analysis employing elements with drilling degrees of freedom are presented. The formulation is based on a variational principle in which displacements and rotations are interpolated independently. The issue of zero masses corresponding to rotational degrees of freedom is addressed and techniques for defining consistent and lumped rotational mass matrices are presented.