结构振动试验转接器的设计及安装问题

一些产品及其相关部件在作振动试验时，由于产品的外形或特殊要求不能直接安装在振动台面上，需要通过特别设计的转接器（夹具）来进行连接，这种夹具实际上是一种附加结构，它作为台面与试件之间的中介，如设置不当将影响振动试验结果的可靠性。本文通过对某事例的分析与研究，从试验频带、允许误差、跟随条件以及安装共振频率等方面阐明与讨论了相关夹具的特性、设计原则与安装等问题。     

光电对抗仿真试验系统综述

论述了研制光电对抗仿真试验系统建设的目的和意义,光电武器系统的现状和发展趋势,介绍了光电对抗仿真试验系统的一般组成,给出了光电武器系统的常规试验内容和试验流程,并论述了可能采用的试验方法。     

有限元技术在数值试井中的应用

分析了试井技术的发展趋势，对有限元分析技术及其发展作了较为全面的介绍，重点阐述了利用有限元技术进行三维建模的方法和步骤，尤其是对复杂的非对称边界和非均质油藏的建模方法和技巧进行了深入探讨。利用数值试井技术，石油工程师可以方便准确地对复杂油藏和边界进行建模，试井的模拟过程和油藏任意位置的压力瞬间变化都可以通过图形和颜色的变化显示出来，解释的精度和速度都得到了大大地提高。     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

射孔枪+内置式压力计托筒+水力泵新三联作试油(测试)工艺技术在大港油田研制与应用

该工艺技术是在原三联作(TCP+MFE+JET)基础上,根据大港油田勘探试油(测试)的需要,研制开发出的又一新技术,与原三联作相比,一趟管柱不但完成求产、测压、泵排工作,而且还能进行酸化等措施,提高了资料品质,减少了作业成本。经过6井次现场应用,全部达到了设计要求,取得了工艺、资料、成本、速度的较大进步,具有较高推广应用价值。     

The hot compaction behaviour of woven oriented polypropylene fibres and tapes. I. Mechanical properties

The aim of this work was to establish the important parameters that control the hot compaction behaviour of woven oriented polypropylene. Five commercial woven cloths, based on four different polypropylene polymers, were selected so that the perceived important variables could be studied. These include the mechanical properties of the original oriented tapes or fibres, the geometry of the oriented reinforcement (fibres or tapes), the mechanical properties of the base polymer (which are crucially dependant on the molecular weight and morphology), and the weave style. The five cloths were chosen so as to explore the boundaries of these various parameters, i.e. low and high molecular weight: circular or rectangular reinforcement (fibres or tapes): low or high tape initial orientation: coarse or fine weave.A vital aspect of this study was the realisation that hot compacted polypropylene could be envisaged as a composite, comprising an oriented ‘reinforcement’ bound together by a matrix phase, formed by melting and recrystallisation of the original oriented material. We have established the crucial importance of the properties of the melted and recrystallised matrix phase, especially the level of ductility, in controlling the properties of the hot compacted composite.     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。