动力配煤高温复合固硫剂研究

分析了高温复合固硫剂各成分的作用，实验研究了在不同配比的燃烧试验下，各成分对燃煤着火和燃烧以及对炉渣固硫的影响，得出了该煤种高温复合固硫剂的最佳配方。     

双层堤基的井涌破坏与无害管涌

双层堤基水文地质结构特殊，堤基承压水常具独特的“渗而不流”特征。在“不流”条件下，堤后盖层薄弱处受超高承压水头顶裂破坏，产生的局部冒水孔实属承压自流井，由此形成的管涌实质为井涌。底部进水的承压井流影响范围不大，井涌的破坏范围更小，据此可区分出有害管涌与无害管涌。前者局限于堤脚附近，小范围压渗为首选方案；对后者，既无需专门防治，更不必追求根治。     

预应力钢-混凝土组合梁的应用与研究

回顾了预应力钢 混凝土组合梁国内外应用与研究历史 ,分析了现有规范及理论的不足 ,并指出了有待解决的问题。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

金属－橡胶硫化粘接过程中分子取向行为的间接证据

对金属－橡胶热硫化粘接复合体的剥离行为进行了研究，同一粘接试样的双向１８０°剥离试验显示出了巨大的差异。本文分析了弹性材料在硫化过程中的分子行为，并提出了相应的新假设，认为这是由于金属－橡胶在硫化粘接过程中分子取向交联行为所致。这种双向１８０°剥离破坏现象可被看作是金属－橡胶硫化粘接过程中分子取向行为的间接证据。     

T_C≥400°C高温PTC陶瓷的研制

利用国产原料，采用传统的陶瓷材料制备工艺，研制了居里温度ＴＣ≥４００°Ｃ的高温ＰＴＣ陶瓷，制成了居里温度ＴＣ＝４１２°Ｃ，电阻Ｒ≤１０３Ω，ｌｇ（Ｒｍａｘ／Ｒｍｉｎ）＝４的高性能ＰＴＣ热敏陶瓷材料     

聚吡咯导电材料合成方法的进展

本文对聚吡咯及聚吡咯导电复合物的合成方法进行了综述。     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

Analysis of adhesive bonded composite lap joints with transverse stitching

The effect of transverse stitching on the stresses in the adhesive is investigated using an adhesive sandwich model with nonlinear adhesive properties and a transverse stitching model for adhesive bonded composite single-lap and double-lap joints. Numerical results indicate that, among all stitching parameters, thread pretension and stitch density have significant effect on the peel stresses in the adhesive; increase in the thread pretension and the stitch density leads to a decrease in peel stress in the adhesive, while an increase in other parameters generally results in a negligible reduction in peel stress. The effect of stitching was found to be negligible on the shear stresses in the adhesive. Thus it is concluded that stitching is effective for the joints where peel stresses are critical and ineffective for those where shear stresses are critical.