高效全自动清淤系统在酸性水库的应用

针对 pH ≤ 3 的酸性水库周边地形复杂无法进入大型机械设备、淤泥沉积深夹带有大量织物、库底覆有土工膜易破损等特点,将前置浮船可升降的水面泥浆输送系统与地面泥浆输送系统串联可实现高浓度远距离管道输送,通过全自动监测,采用智能变频控制,保证系统在泥浆浓度可变、液面高度可变的大范围区间内连续且稳定运行。系统在调试运行期间,抽送高浓度泥浆为 19220.88m3,极大提高了酸性水库的清淤效率,降低了清淤成本。     

低成本钢尾渣-矿渣基矿山充填料的优化开发

 为实现多固废协同利用、降低充填成本,在矿渣基全粒级细尾砂胶结充填料基础上,以流动性和抗压强度为表征,利用热闷钢渣磁选尾渣(钢尾渣)替代部分矿渣作为胶凝材料,脱硫灰和水泥熟料替代部分专用添加剂作为外加剂,采用正交试验探寻掺量规律,优化固体填充料配比,开发钢尾渣-矿渣基软性矿山充填料,并研究了外加剂与胶材比、灰砂比等因素的影响。对比分析了矿渣基准组、钢尾渣-矿渣基准组(B1)、强度最优外加剂组分钢尾渣-矿渣组(B7)等3组充填料的微观形貌及XRD图谱以探究其水化机理。结果表明,钢尾渣替代矿渣量增加、外加剂与胶材比减小,充填料浆流动性改善,但充填体抗压强度下降。强度正交试验结果表明,钢尾渣掺量大小决定强度低高,脱硫灰掺量宜高于水泥熟料。进一步调整外加剂组分配比,在灰砂比为1∶6、钢尾渣替代矿渣为20%条件下,找出B7组外加剂组分为脱硫灰、水泥熟料分别替代30%、20%专用添加剂,B7组料浆扩展度为143 mm,充填体形貌为富铁绿泥石胶结假方体钙硅灰石,28 d抗压强度达2.13 MPa,较基准组低0.19 MPa,较B1提高0.26 MPa。该替代方案满足现场充填C2级强度的要求,改善流动性并显著降低了充填成本。优化的外加剂组分配比在灰砂比为1∶4条件下同样具有强度优化作用,但较灰砂比为1∶6条件下低。     

复合变质处理对铸造热锻模具钢力学性能的影响

研究了变质处理对铸造热锻模具钢力学性能的影响。结果表明：在相同热处理条件下，经RE和RE—Nb复合变质处理后，其冲击韧性与变质处理前相比分别提高了9．7和14．5J／cm^2，常温抗拉强度σb分别提高了82和234MPa，高温抗拉强度分别达到了976和994MPa，而硬度变化不大。     

MICROSTRUCTURE OF RAPIDLY SOLIDIFIED TiAl ALLOY POWDER

The rapidly solidified powder of Ti-34Al-2Mn alloy was obtained by means of ultrasonicgas atomisation (USGA) technique.The tupical size of the powder is 27 μm.X-ray diffractionresults show that the powder consists of major α_2-phase and minor γ-phase.Under opticalmicroscope both equiaxed and dendritical microstructure features were observed on RS pow-der sections.After annealing at 900 ℃/for 2 h in vacuum,most of α_2-phase transforms intoγ-phase,resulting in refinement of structure.     

BEHAVIOR OF Mg AND ITS EFFECT ON MECHANICAL PROPERTIES OF CAST Fe_3Al ALLOYS

Proper addition of 0.002 wt-% Mg to cast Fe_3Al alloy may obviously improve the room andhigh temperature tensile properties.Auger spectra show that Mg segregates near grainboundaries as very thin layers.Observation under TEM reveals that a suitable amount of Mgenhances ability of cooperative internal deformation so that the dislocations will ease the con-tinuous slip deformation through grain boundaries.The fracture feature of Fe_3Al alloy is oftransgranular cleavage at room temperature and cracks initiate at grain boundaries.     

硼对快凝Ni3Al组织结构及力学性能的影响

本文通过快凝及加硼合金化的方法改善金属间化合物Ni_3Al的韧性。实验表明:加入0.5-1.4at.-％的硼对Ni_3Al的塑性提高最有利。结构分析表明:在含1.37at.-％硼的Ni_3Al中,硼以Ni_(23)B_6弥散相及晶界偏聚方式存在;当硼量增至2.22at.-％时,硼以粗大的Ni_(23)B_6及NiB_(12)相在晶界处析出。无硼的Ni_3Al晶界为大角度晶界;当硼加至1.37at.-％时,Ni_3Al晶界以位错排列成亚晶界,以小角晶界形式存在。     

化合物TbMn6Sn6的磁性和磁相变

采用分子场理论模型对稀土-过渡族金属间化合物的磁性、自旋重取向相变和场诱导的一级磁相变进行了研究.从理论上计算了TbMn6Sn6的易磁化方向随温度的变化以及不同温度时的磁化曲线,描述了自旋重取向相变和场诱导的一级磁相变.基于单离子模型计算了Tb离子和化合物的一阶和二阶磁晶各向异性常数及其随温度的变化,得到了和实验数据基本一致的结果.结果表明:Mn次晶格和Tb次晶格磁晶各向异性能之间的相互竞争是导致自旋重取向相变的物理机制,而稀土离子的四阶晶场项对场诱导的一级磁相变产生很大的影响.     

提高电火花加工效率的一种方式

基于离子在电磁场下快速而有规律运动的原理。提出了提高电火花加工效率的一种新策略，一个简单的采用功率场效应晶体管的主电路及它们的逻辑驱动信号也同时在文中提出了和分析。     

Technological condition in slurry electrolysis of high-silver galena concentrate

Effects of various technological conditions such as ρ(C1^- ), ρ(Fe)T, pH value and temperature on the cell voltage, lead leaching rate and the cathodic current efficiency of the slurry electrolysis of high-silver galena concentrate were studied, and the behavior regularity of lead and silver was investigated. As a result, the suitable condition was determinedas, ρ(C1^-)230g/L, ρ(Fe)T15g/L, pH 1, temperature 70℃, electrolysis time 6h. Under such condition,adopting the cathodic current density of 150 A/m2 and the liquid-solid ratio of 15 : 1, lead powder with a purity degree of 91. 18% was got. At the same time, leaching rate of lead, leaching rate of silver and cathodic current efficiency amounted to 96.88%, 70.88% and 75.68% respectively.     

THEORETICAL CALCULATION OF POINT DEFECTS IN Ni_3Al

Equilibrium equation of point defects in Ll_2 type intermetallic compounds was established tocalculate the relations of the concentration of antisite defects and vacancies and bulk composi-tion in Ni_3Al.The examination of temperature effects on the point defects cleared up the mis.understanding of the properties of the“constitutional point defects”in Ni_3Al.