型钢翼缘狗骨式削弱在型钢混凝土节点的作用

为了防止地震时型钢混凝土节点核心区发生剪切破坏以及梁柱连接焊缝发生脆性断裂,提出对型钢混凝土节点核心区附近梁端型钢的上、下翼缘采取狗骨式削弱,并系统研究翼缘削弱对提高型钢混凝土节点抗震性能的作用.研究表明,由于在梁端型钢翼缘采取狗骨式削弱,不仅能够将塑性铰控制在梁型钢削弱的位置,从而有效地降低了节点核心区所受的剪力以及梁柱连接焊缝的应力;而且能够改善节点塑性铰区的转动能力和抗剪性能,提高节点的延性和耗能能力.     

增强Fisher判决的Bagging集成分类方法

提出了一种样本间的相似性度量方法,并将这种相似性度量信息附加到Fisher线性判别的类内、类间离散度矩阵,使得Fisher判决准则在使类内距离迭最小、类间距离迭最大的同时,也使类内相似度迭最小、类间相似度达最大,获得比原始Fisher判剐更好的投影矩阵。实验证明,与Bagging集成的Fisherfaee比较,该方法显示出更好的识别率。     

基于组合单元的圆钢管混凝土结构非线性分析

基于圆钢管混凝土组合截面轴力-应变关系和轴力一弯矩一曲率关系实用计算方法,采用U.L列式单元增量平衡方程,引入平面梁单元非线性分析方法,建立了钢管混凝土结构组合单元法非线性有限元分析理论.编制了相应的非线性有限元程序,对已有钢管混凝土结构的面内受力,如钢管混凝土偏压柱、不等端弯矩钢管混凝土偏压柱、钢管混凝土压弯构件和钢管混凝土模型拱肋等进行双重非线性有限元分析,与基于钢管混凝土拉压数值本构模型的分层梁单元非线性分析理论比较.结果表明,两种分析方法的载荷一变形曲线和极限承载力都很接近试验结果,与分层法相比,组合单元法直接根据杆端力求解截面刚度,不用分层计算截面刚度,加快了计算速度.     

双洞口配筋砌块砌体框支墙梁试验

为研究双洞口配筋砌块砌体框支墙梁地震前后的受力模式,在拟动力子试验前后进行了底层框架配筋砌块短肢砌体剪力墙结构三层足尺模型的竖向力静载试验.试验结果表明:托梁与上部墙体表现出良好的协同工作能力,其工作模式为拉杆拱.通过对其在拟动力试验前后的受力模式进行了比较,可知带洞口配筋砌块砌体框支墙梁结构体系在墙体受到一定损伤时,并不会使墙梁的受力机理发生明显改变.     

CFRP加固钢筋混凝土梁滞后应变计算方法

为了系统研究从零负载状态到满负载状态各个阶段CFRP片材加固梁滞后应变的计算方法,在充分考虑加固梁不同负载状态及受压区混凝土非线性本构关系的基础上,分别建立了不同负载贴片加固梁考虑混凝土抗拉作用时的滞后应变计算公式及不考虑混凝土抗拉作用时的简化计算公式.试验数据和对比分析结果表明:"考虑混凝土抗拉作用"公式的计算结果与试验数据吻合良好,计算误差<8%,明显优于现有文献的计算方法;"不考虑受拉区混凝土抗拉作用"公式的计算结果在混凝土开裂前和试验值相差较大,但对已裂加固梁的计算误差与"考虑混凝土抗拉作用"公式的计算误差接近.为简化计算,对未裂和已裂混凝土梁贴片加固时的滞后应变可分别采用"换算截面"公式和"不考虑混凝土抗拉作用"公式进行计算,两种简化方法的误差均不会超过10%.     

S-P混杂纤维对混凝土长期性能与耐久性影响

采用对比的试验方法,研究并讨论了钢纤维、聚丙烯纤维及其混杂对混凝土长期性能及耐久性的影响.研究结果表明,用不同尺度、不同性质的钢纤维与聚丙烯纤维按二元混杂以总体积率0.9%掺入高性能混凝土中,明显改善了水泥混凝土的长期性能,90d干缩值减少36.6%,200d徐变度降低45.4%,并可显著提高混凝土的耐久性能,相对渗透系数降低79.03%,氯离子渗透系数降低30.5%.     

Corrosion behavior of tempered dual-phase steel embedded in concrete

Dual-phase(DP) steels with different martensite contents were obtained by appropriate heat treatment of an SAE1010 structural carbon steel,which was cheap and widely used in the construction industry. The corrosion behavior of DP steels in con-crete was investigated under various tempering conditions. Intercritical annealing heat treatment was applied to the reinforcing steel to obtain DP steels with different contents of martensite. These DP steels were tempered at 200,300,and 400°C for 45 min and then coo...     

Temperature distribution and dynamic control of secondary cooling in slab continuous casting

To predict and optimize the temperature distribution of slab continuous casting in steady operational state, a three-dimensional model (named offline model) based on the heat transfer and solidification theories was developed. Both heat transfer and flux distribution characteristics of the nozzle sprays on the slab were considered, and the complicated boundary condi-tions, such as spray cooling, natural convection, thermal radiation as well as contact cooling of individual rolls were involved in the model. ...     

Influence of fly ash on early-age cracking behavior of high-flowing concrete

The effects of quality and content of fly ash on the early-age cracking behavior of high-flowing concrete (HFC) were investigated. The early-age cracking behavior of the HFC was analyzed by combining the tests of evaporation capacity and electrical resistivity of the HFC. In these tests, a modified flat-type specimen was adopted. The results show that the HFC will have a lower evaporation capacity when it is mixed with fine fly ash, while it will have a higher evaporation capacity when grade III fly ash is used as mineral admixture. And the electrical resistivity rate of HFC reduces with the increase of the content of fly ash. A nonlinear relationship exists between the cracking time of HFC and the minimum electrical resistivity. The early-age cracking behavior of HFC with fly ash can be enhanced by appropriately increasing the fine particle content and MgO, K₂O, and SO₃ contents of fly ash. The optimal content of fly ash, which makes a satisfied early-age cracking behavior of HFC, is obtained. And when the content of fly ash exceeds a critical value, the early-age cracking behavior of HFC will rapidly decrease. Foundation item: Project(50478003) supported by the National Natural Science Foundation of China; Project(2002F007) supported by the Natural Science Foundation of Fujian Province, China     

考虑冷变形加工硬化的翻边力理论计算

在分析现有计算公式存在不足的基础上,根据翻边变形区材料的应力应变特点,考虑了冷变形加工硬化(取幂函数硬化规律)和变形区材料厚度变化(翻边为变薄)两个因素的影响,利用金属塑性成形问题求解理论中的主应力法,推导和提出了圆孔翻边力计算的一个新公式.通过用钢板(SPCC)和铜板(T1)进行了翻边工艺试验的验证,并与经验公式和现有理论公式的计算结果进行了比较,表明新公式计算结果能接近于实际,且原理上更为科学合理.