大体积砼产生裂缝的原因及防治措施

大体积砼裂缝问题是建筑业普通关心的问题.对砼裂缝进行控制,就必须研究砼结构中裂缝产生的原因以及在实际的设计和施工过程中采取合理的、经济的措施来控制裂缝.本文通过对大体积砼裂缝成因的理论研究,提出了合理的裂缝控制的设计和施工措施.     

Experimental Study of Concrete Subjected to Explosive Loading

The main subject of this paper is to demonstrate the response of structural concrete to different imposed strain rates. Attention is focused on the strain rate about 10^-2 s ^-1>, where some technical difficulties are experienced when an exact determination of mechanical properties for quasi-brittle materials is attempted. The design of a measurement system, which realizes computer acquisition, analysis, and graphic representation of data, is also presented.     

在役钢筋混凝土结构基于可靠性的疲劳寿命分析

本文以结构的极限疲劳循环次数作为随机变量,基于可靠性理论提出了在役结构疲劳剩余寿命的预测方法,分析了多种工况下结构在未来服役期内的疲劳可靠性和疲劳剩余寿命。算例表明,通过对在役结构疲劳寿命及可靠性的分析,不仅可以预测在目标可靠度下的疲劳寿命,而且可以根据需要确定合适的交变荷载的频率、服役时间以及相应的疲劳可靠指标,从而为结构的合理利用起指导性作用。     

针梁台车在大花水水电站引水隧洞混凝土衬砌施工中的改进

大花水水电站引水隧洞由于前期开挖工期略有滞后，为加快施工进度，结合全圆断面的施工特点，大部分引水隧洞采用了全圆针梁穿行式钢模台车进行混凝土衬砌。通过各参建单位对针梁台车的运用和改进，有效地提高了引水隧洞混凝土的衬砌速度，并确保了工程质量。     

洛阳热电厂主厂房地基处理方案的论证

通过对洛阳热电厂拟选择的地基处理方案进行比较,并结合该电厂施工实例论证了φ800/1600扩底钢筋混凝土灌注桩是最适于该电厂及相似地区的地基处理方式。     

曹娥江大闸闸墩混凝土高温季节温控措施

曹娥江大闸是国内最大的河口大闸,其中闸墩施工在夏季高温季节进行.较全面地阐述了混凝土原材料取料温度值的选取及控制措施,已浇筑混凝土内外温差及降温速率的控制措施等.根据闸墩的结构及边界条件,为了控制温度应力防止裂缝的产生,在施工过程中采取了骨料预冷、冷水拌和、掺冰屑拌和、仓面遮阳、内部通冷却水及外侧保温等综合温控措施,确保了闸墩混凝土的施工质量.     

三峡水电站坝后钢衬钢筋混凝土压力背管的非线性有限元分析

采用钢筋混凝土非线性有限元方法，对三峡水电站钢衬钢筋混凝压力管道结构进行了计算，求得了各种钢材配置下的荷载效应并进行了相应的分析。     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

Experimental Study on the Effect of Steel-fibre in Conerete Thick Cap

The effect of steel fibre used in concrete was systematically analyzed by model testing of 30 2-pile thick caps of steel-fibre reinforced concrete, in which the model scale was 1：5. The experiment system composed of a loading device, strain measurement system and a data-acquisition system was used, also an electromechanic centigrade scale, a lens and a Y J-25 static resistance strainometer were used.The experimental results show that the volumetric rate of steel fibre and draw ratio have an important influence on its load-bearing capacity. The incorporation of steel fibre can effectively improve the extension and reduce the thickness of the caps.     

A limit analysis of nonlinear elastic lateral displacements of thin-walled reinforced and prestressed beams

An incremental iterative process based on direct energy minimization is presented for a limit analysis of nonlinear elastic lateral displacements and twists of reinforced and prestressed beams. Problems encountered with the constitutive relations are discussed and two possible material models are presented.