大窝山隧道进口围岩快速掘进施工组织与管理

结合工程概况及工程特点,从机械设备配置、劳动力组织、现场管理等方面介绍了大窝山隧道进口Ⅱ级,Ⅲ级围岩段的快速掘进施工组织与管理措施,为类似隧道的快速掘进施工组织与管理提拱了相关经验.     

Structure of rapidly solidified aluminum alloys

This paper is a summary of an extensive research program carried out by the authors on the structure of rapidly solidified aluminum alloys; and a comparison with the work of others also involved in this field. The paper discusses the changes in the dendritic and non-dendritic structure of the matrix at cooling rates from 10^–3 to 10¹⁰ K/s and discusses the hetergeneity of the structure caused by interdendritic-segretion during solidification.     

YAG激光熔覆的研究现状与发展趋势

本文介绍了YAG激光熔覆的特点，并与CO2激光进行了比较，显示了YAG激光熔覆的优势和潜力。叙述了YAG激光熔覆的研究进展及其应用前景。     

Pd-Ge contact to n-GaAs with the TiW diffusion barrier

Pd-Ge based ohmic contact to n-GaAs with a TiW diffusion barrier was investigated. Electrical analysis as well as Auger electron spectroscopy and the scanning electron microscopy were used to study the contact after it was subjected to different furnace and rapid thermal annealing and different aging steps. All analyses show that TiW can act as a good barrier metal for the Au/Ge/Pd/n-GaAs contact system. A value of 1.45 × 10⁻⁶ Ω-cm² for the specific contact resistance was obtained for the Au/TiW/Ge/Pd/n-GaAs contact after it was rapid thermally annealed at 425°C for 90 s. It can withstand a thermal aging at 350°C for 40 h with its ρ_c increasing to 2.94 × 10⁻⁶Ω-cm² and for an aging at 410°C for 40 h with its ρ_c increasing to 1.38 × 10⁻⁵ Ω-cm².     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Targets and methods for the detection of processed animal proteins in animal feedstuffs

Bovine spongiform encephalopathy (BSE), or ‘mad cow disease’, is one of several transmissable spongiform encephalopathies (TSEs) known to affect certain mammals and is spread through the ingestion of infected animal tissue. It is believed that the inadvertent contamination of meat and bone meal (MBM) with infected animal tissue and the subsequent use of this material as a feed supplement contributed to the spread of the disease in cattle. As a result, the use of processed animal proteins (PAPs) in animal feeds is regulated in many parts of the world. Although feed testing is the only definitive means to certify compliance, regulatory compliance often relies solely on paper certification. Recently, rapid methods have become available that can be used by regulators to determine compliance during routine inspections. We describe a rapid, immunochromatographic strip test that can detect 0.1% MBM in animal feed. The test takes 15 min to perform and large numbers of samples can be screened for PAPs simultaneously.     

喷雾沉积快速凝固技术的发展与展望

喷雾沉积是制取大体积快凝材料的一种新工艺。本文综述了它的产生和发展，概述了其基本原理和过程控制。对该领域今后的发展动向，提出了一些新看法。     

露采边坡渗流的有限元分析及其实例

介绍了应用有限元法求解渗流问题的原理及其实例。     

金属快速凝固方法的数学模型

本文综述了与几种典型的快速凝固方法相应的数学模型，并对每种模型作了相应的分析和评价。文中重点介绍了“活塞－砧法”，“双辊法”，“单辊法”和“雾化沉积法”数学模型的理论基础，建模过程，理论优缺点及实用局限性。     

重油催化裂化反应技术的新进展

近十几年来，重油催化裂化技术作为主要的重质油轻质化手段得到了迅速发展，国内外围绕催化裂化装置的提升管反应器也开发了许多新技术。综述了重油催化裂化反应技术的新进展，并对新技术的开发进行了讨论。