膨胀剂对约束条件下UHPC早期抗裂性能影响的试验研究

超高性能混凝土(UHPC)在钢桥面铺装结构中由于铺装材料受到钢板、栓钉等的约束,加上材料本身水胶比小,更易收缩,早期容易承受拉应力导致开裂。通过在拌和过程中添加膨胀剂可以起到减小收缩的作用,但该方法对于约束条件下的UHPC铺装的早期抗裂性能提升是否有促进作用,仍需通过更多试验进行合理评估和深入研究。通过圆环法对3组不同配方的UHPC在均匀约束条件下的早期抗裂性能进行定量测试,并将试验数据进行回归分析和计算,得到了各组的平均应力发展速率,进而评估了各组的开裂风险等级。试验结果表明,通过在UHPC中加入适量膨胀剂,可使其最终收缩应力减小,并可降低其收缩应力发展速率,进一步降低其在约束条件下的开裂风险。     

寒冷地区高温干燥条件下混凝土面板裂缝控制

希尼尔水库位于新疆巴音郭楞蒙古族自治州境内，气候特点为高温、干燥、冬季寒冷。根据混凝土面板产生裂缝的原因，并结合工程区的气候特点，认为控制面板的塑性收缩、干缩与冷缩裂缝是防止裂缝产生的重点。通过采用高性能混凝土，合理的养护措施(微喷灌洒水技术)，有效地防止了裂缝的产生，保证了工程质量。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。     

墙体裂缝的成因及防治

介绍了墙体裂缝的种类，从地基不均匀下沉、温度变化等方面分析了引起墙体裂缝的原因，介绍了墙体裂缝的预防措施和治理措施，以有效控制墙体裂缝的危害程度。     

一般阵列误差情况下信号二维方向角估计

针对均匀圆阵存在一般阵列误差的情况,提出一种信号二维方向角估计方法.基于均匀圆阵的阵列流形和阵列输出的协方差矩阵,采用加权总体最小二乘法估计信号二维方向角.并给出了解整周期性模糊的方法.计算机仿真表明了此方法估计精度高,对阵列误差鲁棒性强,并且各项性能都接近于CRB.     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

X80焊管H_2S环境应力腐蚀开裂行为研究

采用三点弯曲加载法和微电极扫描测试技术,研究了X80高强度级管线钢及其焊缝区的抗H2S环境应力腐蚀开裂(SSCC)行为。测定了焊接接头的显微硬度分布,分析了显微组织结构、力学性能及抗腐蚀性能之间的相关性。研究表明,热影响区(HAZ)对应力腐蚀开裂最为敏感,母材的纵向和横向取样对应力腐蚀敏感性影响不显著,薄壁管材比厚壁管材有较好的抗H2S环境应力腐蚀性能。HAZ晶粒粗大、硬度高,局部腐蚀倾向大,由此导致该区SSCC敏感性高。     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

一种基于空间到达角的卫星电子侦察信号分选方法

在建立简化的卫星电子侦察空间模型的基础上，提出了一种利用空间到达角分选卫星电子侦察信号的新方法。通过仿真实验验证了这种方法的可行性。该方法可用于密集信号的预处理。     

不同表面预处理对有机电致发光显示器性能的影响

从生产角度研究了基板表面的预处理工艺对OLED性能的影响,分别用UVOzone、氧Plasma以及两者相结合的方式对基板进行表面处理,并按照生产工艺制作器件,从接触角、方阻以及光电特性等测试结果对各种表面处理的样品进行比较。结果表明以上处理都改善了器件性能,不同程度提高了器件的清洁度、亮度和发光效率,其中UVOzone和氧Plasma结合的方式处理效果最为显著,器件在10V时亮度达到79920cd/m2,比其他两种处理方式亮度提高约25%。