Effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy

The CuCrZr alloy undergoes processes of precipitation during ageing. Besides precipitation hardening the strength is affected by cold deformation which is performed before and after ageing. The cold deformation (D ₁) before ageing accelerates the process of strength hardening, since it induces higher rate of precipitation from the saturated a-sold solution. Cold deformation (D ₂) after ageing primarily affects the alloy strength. In this paper the results of the effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy are presented. The aim of the paper was to evaluate the most suitable combination of thermomechanical treatment and alloy properties.     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

粘弹性圆柱壳在轴向恒压下的动力稳定性

基于Timoshenko-Mindlin假设,得到考虑粘弹性的各向同性圆柱壳及纤维增强正交铺设层合圆柱壳在轴向恒压下的动力学方程。文中对两端简支的圆柱壳进行了分析,依Laplace变换,导出动力稳定的特征方程,由Routh-Hurwitz判据建立动力稳定性条件,对两类圆柱壳讨论了横向剪切变形的影响。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

混凝土简支梁预设变形值探讨

以某高速公路钢筋混凝土与预应力混凝土工程为例，从简支梁的预拱度和下挠度的设置两方面进行了阐述，提出了钢筋混凝土简支梁下挠变形和预应力混凝土简支梁上拱变形的不同之处。     

大规模集成电路浮栅ROM器件总剂量辐射效应

提出了一种大规模集成电路总剂量效应测试方法:在监测器件和电路功能参数的同时,监测器件功耗电流的变化情况,分析数据错误和器件功耗电流与辐射总剂量的关系.根据该方法利用60Co γ射线进行了浮栅ROM集成电路(AT29C256)总剂量辐照实验,研究了功耗电流和出错数量在不同γ射线剂量率辐照下的总剂量效应,以及参数失效与功能失效时间随辐射剂量率的变化关系,并利用外推实验技术预估了电路在空间低剂量率环境下的失效时间.     

胜利油田污水储罐腐蚀防护方法评价

对胜利油田纯粱采油厂A3钢制生产污水（水温约60℃）储罐使用寿命过低的原因进行了实验考察。水质分析数据表明氯离子浓度高（45-48gm）是污水腐蚀性强的主要因素。A3钢在60℃污水中的腐蚀速率，由极化曲线数据计算的值大大高于失重法测定值，敞开系统中失重法测定值又高于密闭系统中测定值，挂片上出现蚀孔，说明储罐中A3钢发生了氧存在下氟离子引起的局部腐蚀（孔蚀）。元素分析结果表明．储罐阴极保护所用的牺牲阳极铝材含铁等元素量超标。牺牲阳极密封不良，在实验污水中7天后电流效率仅为2．92％，失去阴极保护能力。处于实验污水环境中的有涂层保护的A3钢．14天后出现腐蚀极化电流，表明涂层已失去完整性。要提高该采油厂及胜利油田其他采油厂污水储罐的使用寿命，必须改用合格的牺牲阳极和保护涂层材料。图3表2参7。     

碎丝埋弧焊在大型立式储罐中的应用

大型储罐底板焊接及变形控制是保证储罐整体施工质量的关键环节,采用碎丝填充的焊接方法可以防止变形,同时可以有效地避免应力集中,提高施工质量。文章介绍了碎丝埋弧焊的原理、工艺参数和焊接方法。实践证明,填充碎丝不仅是一种减小底板焊接变形的手段,同时可以充分利用焊接热能,节约焊接时间和焊剂用量,经济效益好,是一种值得推广的技术。     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

Defect structure of gold introduced by high-speed deformation

The effect of deformation speed on defect structures introduced into bulk gold specimens at 298 K has been investigated systematically over a wide range of strain rate from ′=10⁻² to 10⁶ s⁻¹. As strain rate increased, dislocation structure changed from heterogeneous distribution, so-called cell structure, to random distribution. Also, stacking fault tetrahedra (SFTs) were produced at anomalously high density by deformation at high strain rate. The anomalous production of SFTs observed at high strain rate is consistent with the characteristic microstructure induced by dislocation-free plastic deformation, which has been recently reported in deformation of gold thin foils. Thus, the results of the present study indicate that high-speed deformation induces an abnormal mechanism of plastic deformation, which falls beyond the scope of dislocation theory. Numerical analysis of dislocation structure and SFTs revealed that the transition point of variation of deformation mode is around the strain rate of 10³ s⁻¹.