Carbon coating of anatase-type TiO2 through their precipitation in PVA aqueous solution

Fine particles of photocatalytic anatase-type TiO₂ prepared through hydrolysis of titanium-tetraisopropoxide were coated by carbon through their precipitation in poly(vinyl alcohol) (PVA) aqueous solution, followed by heat treatment at high temperatures of 400-1000 °C in a flow of high purity Ar. Without carbon coating, the phase transformation from anatase to rutile started above 600 °C, but it was suppressed up to 800 °C with carbon coating. Suppression of the phase transformation depended on the amount of carbon coated, apparent suppression being observed with carbon content above 5 mass%. The amount of carbon coated on anatase was controlled by changing the concentration of PVA in the solution. In order to have a carbon content of about 5 mass%, a PVA solution with more than 2 mass% had to be used.     

Preparation and characterization of trilobal activated carbon fibers

The objective of this research was to evaluate the effectiveness of several different methods for controlling the pore size and pore size distribution in activated carbon fibers. Variables studied included fiber shape, activation time, and the addition of small amounts of silver nitrate. Pure isotropic pitch and the same isotropic pitch containing 1 wt.% silver were melt spun to form fibers with round and trilobal cross sections. These fibers were then stabilized, carbonized, and activated in carbon dioxide. Field emission scanning electron microscopy (FE SEM), electron dispersive spectra (EDS), and wavelength dispersive spectra (WDS) were used to monitor the size and distribution of the silver particles in the fibers before and after activation. Each of these analyses showed that the distribution of silver particles was extremely uniform before and after activation. The fibers were also weighed before and after activation to determine the percent burn-off. The BET specific surface areas of the activated fibers were determined from N₂ adsorption isotherms measured at −196 °C. The results showed that round and trilobal fibers with equivalent cross-sectional areas yielded similar burn-off values and specific surface areas after activation. Also, activation rates were found to be independent of CO₂ flow rate. The porosity of the activated fibers depended on the total time of activation and the cross-sectional area of fibers. The N₂ adsorption measurements showed that the activated fibers had extremely high specific surface areas (greater than 3000 m²/g) and high degrees of meso- and macro-porosity. FE SEM was also used to investigate surface texture and size of pore openings on the surfaces of the activated fibers. The photos showed that silver particles generated surface macro- and mesopores, in agreement with the inferences from N₂ adsorption measurements.     

Pore structure of carbons coated on ceramic particles

Pore structure of carbon coated on ceramic particles by carbonization of precursor in a powder mixture at 900 °C was studied by focusing on the effects of substrate ceramics (MgO, TiO₂ and various phases of Al₂O₃) and of carbon precursor (poly(vinyl alcohol) (PVA), poly(ethylene terephthalate) (PET) and hydroxyl propyl cellulose (HPC)). By dissolving substrate MgO particles, carbon coated was found to have a high BET surface area, more than 1000 m²/g, which was almost the same as the value estimated from apparent surface area measured on carbon-coated MgO particles under the assumption of zero surface area of the substrate. The carbon separated was found to be rich in micropores from the analyses by DFT method and α_s plot. The dependence of the BET surface area on the amount of carbon coated on TiO₂ with a high surface area was the same for three carbon precursors, although the carbon yields from the precursors were slightly different. Porous Al₂O₃ substrates, γ-Al₂O₃as-received and that formed from Al(OH)₃ during carbonization, gave a high BET surface area, but dense Al₂O₃, α-Al₂O₃, gave a low surface area.     

Preparation and characterization of antibacterial silver-dispersed activated carbon aerogels

Silver-dispersed carbon aerogels (CAs) were obtained by direct immersion of organic aerogels prepared by ambient pressure drying technique in AgNO₃ aqueous solution and then carbonization. The effect of preparation conditions such as the resorcinol/catalyst ratio, the feed AgNO₃ concentration, the ratio of aerogel mass/solution volume, immersion time and carbonization temperature on the bulk density and silver content as well as the BET surface area of the dispersed CAs was studied. The dispersion and structure of silver nanoparticles in obtained materials were investigated by means of scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The Ag-dispersed CAs prepared exhibit strong and long-term antibacterial activity.     

Simultaneous measurement of flow pattern and mass transfer coefficient in bubble columns

Mass transfer studies were carried out in a bubble column using the chemical method. Catalytic oxidation of sodium sulfite was chosen for the studies and the corresponding specific rates of oxidation were obtained using a stirred cell. Laser Doppler anemometer (LDA) was used to measure the instantaneous velocities in the same stirred cell as well as in bubble columns (100 and i.d.). An efficient algorithm based on the multiresolution analysis of the velocity-time data using wavelets was used for the isolation of data belonging to the gas and liquid phases. Eddy isolation model was used for the characterization of the eddy motion including the estimation of the energy dissipation rate. Using the knowledge of eddy motion, a methodology was developed for the prediction of true mass transfer coefficient (k_L) in a stirred cell as well as in bubble columns. The predicted values of k_L have been compared with the experimental values obtained by the chemical method.     

Fe2O3和K2CO3对高灰分煤催化燃烧影响及机理分析

为提高淮北矿区高灰分煤的燃烧效率,采用热重分析实验对比分析了Fe2O3和K2CO3对煤粉着火与燃尽温度、燃烧特性指数、放热面积的影响.结果发现Fe2O3和K2CO3可分别将煤粉的着火温度由480.3℃降低470.4℃和397.3℃,燃尽温度由628.4℃降到609.7℃和547.7℃,燃烧特性指数提高,放热量增大.利用SEM、XRD和FTIR测试技术对煤粉燃烧残余物的微观结构、物相组成及官能团变化进行研究,分析燃煤催化剂在燃烧反应中的作用机理;通过BET方程计算燃烧煤焦的比表面积,分析其孔隙结构的变化.结果表明Fe2O3和K2CO3的主要作用机理是促进燃烧反应过程中挥发分的析出,增强煤粉的吸附性能,加快燃烧反应过程中固定碳的燃烧.     

Effect of microstructure on the electrochemical performance of Ni-ScSZ anodes

The effects of NiO powder morphology and sintering temperature on the microstructure and the electrochemical performance of Nickel-scandia-stabilized zirconia (Ni-ScSZ) cermet anodes for solid oxide fuel cells (SOFCs) were investigated. The particle size and agglomeration of the starting powders were found to affect both the microstructure and electrochemical performance of the Ni-ScSZ cermet anodes. The lowest polarization resistance, 0.690 Ω cm² at 700 °C, was measured for the Ni-ScSZ anode prepared with fine NiO powder (~0.5 µm grain size). This was attributed to the increase in the number of reaction sites afforded by the small grains and well-dispersed Ni and ScSZ phases. The effect of the anode sintering temperature was also found to affect the anode microstructure, adhesion with the electrolyte, and consequently anode polarization resistance. The lowest polarization resistance was observed for the anode sintered at 1400 °C and this was 3–5 times lower than the corresponding values for anodes sintered at lower temperatures.     

Transcranial Magnetic Stimulation of the Supplementary Motor Area in the Treatment of Obsessive-Compulsive Disorder: A Multi-Site Study

Recently, strategies beyond pharmacological and psychological treatments have been developed for the management of obsessive-compulsive disorder (OCD). Specifically, repetitive transcranial magnetic stimulation (rTMS) has been employed as an adjunctive treatment in cases of treatment-refractory OCD. Here, we investigate six weeks of low frequency rTMS, applied bilaterally and simultaneously over the sensory motor area, in OCD patients in a randomized, double-blind placebo-controlled clinical trial. Twenty-two participants were randomly enrolled into the treatment (ACTIVE = 10) or placebo (SHAM = 12) groups. At each of seven visits (baseline; day 1 and weeks 2, 4, and 6 of treatment; and two and six weeks after treatment) the Yale-Brown Obsessive Compulsive Scale (Y-BOCS) was administered. At the end of the six weeks of rTMS, patients in the ACTIVE group showed a clinically significant decrease in Y-BOCS scores compared to both the baseline and the SHAM group. This effect was maintained six weeks following the end of rTMS treatment. Therefore, in this sample, rTMS appeared to significantly improve the OCD symptoms of the treated patients beyond the treatment window. More studies need to be conducted to determine the generalizability of these findings and to define the duration of rTMS’ clinical effect on the Y-BOCS. Clinical Trial Registration Number (NCT) at www.clinicaltrials.gov: {"type":"clinical-trial","attrs":{"text":"NCT00616486","term_id":"NCT00616486"}}NCT00616486.     

Oxygen vacancies as a link between the grain growth and grain boundary conductivity anomalies in titanium-rich strontium titanate

Titanium-rich (Sr/Ti?=?0.995) strontium titanate (ST) ceramics, air-sintered in a temperature range of 1400–1625?°C, were reported to possess anomalies in the grain growth and analogous anomalies in the grain boundary (GB) conductivity activation energy. However, these two interface-related phenomena, occurring at GBs, could not be associated with each other using a simple “brick-layer” model. In this work we revise the topic and advocate that the deviation from the model comes from the oxygen vacancies localized at GBs of the rapidly-cooled ST ceramics. To verify this, we annealed the ceramics in oxygen and performed their systematic and comparative analysis using impedance spectroscopy. A levelling-off in the GB conductivity activation energy, which increases for ≤1.24?eV, and a four-fold decrease in the GB permittivity are observed after annealing. Thus, we confirm a key role of oxygen vacancies in relation between the grain growth and GB conductivity anomalies of as-sintered Ti-rich ST ceramics.     

Mullite-bonded SiC-whisker-reinforced SiC matrix composites: Preparation,characterization, and toughening mechanisms

A novel mullite-bonded SiC-whisker-reinforced SiC matrix composite (SiCw/SiC, SiC whisker-to-SiC powder mass ratio of 1:9) was designed and successfully prepared. Before preparing the composite, the inexpensive lab-made SiCw was first modified by an oxidation/leaching process and then coated with Al₂O₃. The kinetics results indicate that the oxidation process can be described by improved shrinking-cylinder models. The aspect ratio of SiCw improved after modification. Subsequently, raw materials with a SiC–SiO₂–Al₂O₃ triple-layered structure were obtained after the Al₂O₃-coating process and used as feedstocks during the subsequent hot-pressing sintering. Finally, the characterization of the composites indicates that the mullite-bonded sample performs better (relative density of 93.8?±?1.4%, flexural strength of 533.3?±?18.2?MPa, fracture toughness of 13.6?±?2.1?MPa?m^1/2, and Vickers hardness of 20.6?±?2.5?GPa) than the reference sample without the mullite interface. The improved toughness could essentially be attributed to the moderately strong interface bonding and effective load transfer effects of the mullite interface.