PDC钻头在胜利油田深井钻井中的应用

胜利油田为提高深井钻井速度，试验应用了PDC钻头，结果表明，深井钻井应用PDC钻头可大幅度提高机械钻速，缩短建井周期，降低钻井成本，经济效益明显。通过大量的现场试验，扩大了PDC钻头在胜利油田的使用范围，并取得很好的效果，初步形成了PDC钻头推广应用区域模式。详细介绍了胜利油田不适用PDC钻头钻进的地层岩性，给出了钻头选型及钻井参数选择原则，并对应用效果进行了分析。     

时效处理对 TiNi 合金相变与性能的影响

通过用ＴＥＭ等方法研究热处理制度（固溶处理、时效处理）对ＴｉＮｉ合金相变组织和性能的影响，找出了最佳热处理制度。结果表明，在４５０～５００℃进行时效处理，Ｔｉ－５０．８ａｔ％Ｎｉ的合金出现了大量的Ｔｉ３Ｎｉ４相，且恢复率最高。     

PWR核电站蒸汽发生器停堆湿保养工况联氨的缓蚀作用

一、引言压水堆(PWR)核电站蒸汽发生器(SG)管材因二回路系统腐蚀产物积累发生应力腐蚀开裂,这是SG传热管破损的主要原因之一。维修和更换SG使PWR停运期间所需要的替用电力对发电站造成很大的财政负担,同时,二回路系统的腐蚀产物沉积在蒸汽发生器内,降低     

Bandwidth allocation algorithms for weighted maximum rate constrained link sharing policy

This paper addresses the problem of bandwidth allocation under the weighted maximum rate constrained link sharing policy and proves a key theory in the condition of allocation termination. We propose several algorithms with various worst-case and average-case time complexities, and evaluate their computation elapse times.     

一种流水型40 MSPS高速采样保持器

通过理论分析和实验仿真,提出了一种流水型高速采样保持器电路(S/H)。采用4个采样率为10 MSPS的S/H,构成一个流水型电路结构的S/H,采样率达到40 MSPS。文章提出的电路结构,在一定程度上解决了采样速率与精度的矛盾关系,可以在组合S/H精度等同于单个S/H精度的前提下,将组合S/H采样速率提高到单个S/H的数倍。     

高速连续数据记录系统中双页缓存的设计和实现

在高速连续数据记录系统中，存储设备需要速度匹配单元来实现高速连续数据记录，文章讨论了双页缓存在高速连续记录系统中的作用，并以实际开发的记录系统为例，详细介绍了双页缓存的设计和实现。     

Effects of electrode arrangement and pressure on synthesis of diamond films by arc discharge plasma jet chemical vapor deposition

The setup and deposition conditions of electrode arrangement and pressure have been studied to synthesize diamond films at high growth rate on wide area efficiently by arc discharge plasma jet chemical vapor deposition. An apparatus has been used in which four plasma torches, one is used for cathode and the others for divided anodes, are arranged and the positions of these torches are changeable. Growth rate, deposition area and thickness of diamond films have increased with changing the electrode arrangements without improvement of thickness variation. Maximum growth rate of our apparatus has occurred at the pressure of 6.7 kPa and diamond films that have less variations of quality and surface roughness have been synthesized at lower pressure during deposition. Moreover, a high conversion rate, which is the ratio of carbon atoms that form diamond in supplied methane gas, of 16% has been obtained at the pressure of 6.7 kPa and methane concentration of 2%.     

Film morphology and reaction rate for the CVD of tungsten by the WF6—SiH4 reaction

Journal of Electronic Materials - Low pressure chemical vapor deposition (LPCVD) of tungsten (W) by SiH4 reduction of WF6 on Si(100) surfaces was studied in a single-wafer, cold-wall reactor over a...     

HDPE的耐磨蚀性与抗冲击性的研究

用自制的旋臂式磨蚀实验仪，研究了５种高密度聚乙烯和１种顺丁橡胶改性的高密度聚乙烯，在铁尾矿和铁精矿浆体中的耐磨蚀性。耐磨蚀性最差的是ＨＤＰＥ２２００Ｊ，耐磨蚀性较差的是ＨＤＰＥ６３００Ｍ；ＨＤＰＥ５０００ｓ，６０９８和２４８０的耐磨蚀性较好；ＨＤＰＥ／ｃｉｓ－ＢＲ的耐磨蚀性最好。     

The integral experiment on beryllium with D-T neutrons for verification of tritium breeding

A clean benchmark experiment on beryllium was performed with D-T neutrons at the FNS facility of the Japan Atomic Energy Agency. The main objective was to verify the integral data related to the tritium production on lithium isotopes. Tritium production rates, as well as activation reaction rates were measured inside the beryllium assembly that was shaped as a pseudo-cylindrical slab with an area-equivalent diameter of 628 mm and a thickness of 355 mm. Experimental results were analyzed with a three-dimensional Monte Carlo transport code MCNP-4C and FENDL/MC-2.0, JENDL-3.2/3.3 neutron transport libraries. Evaluation of reaction rates was based on the cross section data taken from the JENDL Dosimetry File and ENDF B-VI data libraries. Analysis shows that all calculation combinations (transport and activation cross section libraries) used for evaluation of reaction rates give data that is agreeable with measured values within 10%.