辽宁省2000年夏季干旱分析

本文针对辽宁省2000年发生的干旱,从大气环流、气候、降水、径流、水资源量等方面,较系统地阐述了各因素的发展规律、特点及物理成因。采用降水指标、径流指标、受旱率进行干旱程度分析。评价出辽宁省2000年干旱为特大干旱。     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

已二醇二丙烯酸酯对真丝的接枝改性研究

研究了用二醇二丙烯酸酯为接枝单体、过硫酸铵（APS）为引发剂对真丝的接枝共聚反应，分析了接枝率的影响素，并测试了改性真丝的主要应用性能。结果表明：乳液和乙醇/水为溶剂的2种体系都能在真丝上获得较高接枝率。对于乙醇/水体系v(乙醇）：v(H2O）=1:1，接枝单体20～30g/L,2%甲酸4ml，引发剂APS 0.5g/L,65～70℃接枝60min的接枝率高。改性后真丝的断裂强度、延伸度、吸湿性能都可获得改善，对酸、碱的溶解性提高，但染色性能提高不明显，对泛黄性改善一般。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

二极管端泵浦连续激光器激活介质长度与透过率的优化

从准三能级系统的速率方程出发,推导出了二极管(LD)端泵浦连续工作端面泵浦固体激光器的速率方程,提出了计算连续LD端面泵浦激光器输出功率的方法,并表示成激活介质长度和透过率的函数,由此得到在泵浦功率一定情况时的优化设计步骤。数值计算结果与我们的实验结果和文献[3],[4]的实验数据符合甚好。     

积极开展泵站技术改造

为探索山丘地区中小型泵站技术改造的经验，选定南康县四个小型泵站作为泵站改造的试点站，进行现场测试，根据测试成果，分析各站存在的问题及效率偏低的原因，并拟定各站技术改造的措施，经实施后取得了较好的效果，本文就南康县泵站改造的实际效果阐明泵站改造的必要性及其改造过程中值得注意的问题。     

Analysis and Optimization Laminar Viscous Flow Through a Channel

Optimizing of laminar viscous flow through a pipe by two dimensionless values is investigated analytically. Dimensionless entropy generation and pumping power to heat transfer rate ratio are used as basis for constant viscous and the temperature dependence on the viscosity. For this matter we calculate entropy generation and pumping power for a fully developed in a pipe subjected to constant wall temperature for either constant viscosity and the variable viscosity. The variation entropy generation increase along the pipe length for viscous fluid is drawn, either the variation summation dimensionless entropy generation and the pumping power to heat transfer rate ratio are varying the fluid inlet temperature for fixed pipe length and are varying pipe length for fixed fluid inlet temperature are drawn. For low heat transfer conditions the entropy generation due to viscosity friction becomes dominant and the dependence of viscosity with the temperature becomes essentially important to be considered.     

辽宁省节水工作存在问题及对策

辽宁省是水资源严重短缺的省份之一，水资源不足已成为制约全省经济社会可持续发展的瓶颈。通过对全省大型取用水户的调查分析，找出了辽宁省节水工作中存在的问题，提出了节约用水工作的对策和建议。     

底水油藏射孔优化设计

为了优化底水油藏的生产参数，研究了不同产量时射孔长度的优化方法。采用球面流和径向流相结合的模型推导了临界产量和无水采油量的计算公式，分别以临界产量和无水采油量为标准，对胜利油田桩西区块底水油藏上6口油井的射孔长度进行了优化设计，优化结果表明，对于底水油藏应首先按照临界产量对射孔长度进行优化设计，如果得到的最大临界产量不符合实际生产的要求，就应按照无水采油量进行射孔优化设计。研究表明，当油井产量超过临界产量后，以临界产量为标准得到的优化射孔长度会减小油井的无水采油量。