利用电阻场板提高SOI-LIGBT的性能

通过在SOI-LIGBT中引入电阻场板和一个p-MOSFET结构,IGBT的性能得以大幅提高.p-MOSFET的栅信号由电阻场板分压得到.在IGBT关断过程中,p-MOSFET将被开启,作为阳极短路结构起作用,从而使漂移区的过剩载流子迅速消失,IGBT快速关断.而且由于电场受到电阻场板的影响,使得过剩载流子能沿着一个更宽的通道流过漂移区,几乎消去了普通SOI-LIGBT由于衬偏造成的关断的第二阶段.这两个因素使得新结构的关断时间大大减少.在IGBT的开启状态,由于p-MOSFET不导通,因此器件的开启特性几乎与普通器件一致.模拟结果表明,新结构至少能增加25%的耐压,减少65%的关断时间.     

Viscoelasticity of oxidized starch/low methoxy pectin mixtures in the presence of glucose syrup

The structural properties of mixtures of pectin, oxidized starch and glucose syrup were investigated using small deformation dynamic oscillation. In the absence of added calcium, preparations of low methoxy pectin with glucose syrup formed viscous solutions, which remained crystal-free at subzero temperatures. Samples of oxidized starch and glucose syrup, on the other hand, exhibited solid-like behaviour because of the crystalline nature of the amylose-like helices. Mixtures of the two polysaccharides with the co-solute clearly showed phase inversion from liquid to solid-like behaviour with increasing amounts of starch in the formulation. The transformation was reflected in the textural properties of samples, which varied from thick solutions to firm gels. The viscoelasticity of the system was modified further by the introduction of high methoxy pectin. Preparations of high methoxy pectin and glucose syrup formed rubbery gels whose amorphous nature underwent a glass transition during cooling.     

约束层阻尼夹芯板动态特性分析

本文给出了新的建立约束层阻尼薄板动力学模型的方法。粘弹性材料的本构关系随温度和频率变化,难以对粘弹结构进行动特性分析及控制研究,本文采用GHM方法描述弹性材料的本构关系,将粘弹性材料的动力特性描述与工程上最常用的有限元分析结合起来,建立了悬臂约束层阻尼板的动力学模型,计算了约束层阻尼夹芯悬臂板的模态参数,计算结果同其它方法相比,精度高且更接近于实验结果,同时与ANSYS5.5及NASTRAN70.7的计算结果基本一致,表明本文给出的方法是准确可靠的。     

新型压滤机液压控制系统的研制

 针对压滤机的工艺要求，在对新型压滤机液压控制系统研究设计的基础上，利用功率键合图方法建立了压滤机液压系统数学模型，并运用Matlab语言进行动态特性仿真．在压滤机现场实际运用表明该系统性能达到了预期目标，为压滤机液压系统优化设计提供了依据．     

大同煤矿集团公司供水处局域网的开发和应用

介绍了大同煤矿集团公司供水处处级局域网的设计原则及开发过程，对外级局域网1年来取得的管理效果、经济效益、社会效益进行了简明的阐述。     

DC-DC变换器突加负载时的动态性能研究

提出了一种能够有效改善DC-DC变换器动态性能的方案。该方案是在全桥电路基础上并联一单端正激变换电路，使变换器负载从10%轻载突加到100%满载时，其暂态过程小于1μs输出电压达到设计要求。文中对具体电路进行了详细分析，并通过仿真进行了验证。     

基于PLC电液比例控制的液力测功装置开发及其应用

本文介绍一种齿轮动态加载试验规范及技术要求，论述了运用电液比例控制技术所设计的液压加载系统原理及其使用效果，并简述由此构造的液力测功装置的原理与应用前景。     

无线移动自组网络的动态源路由策略

文章介绍无线移动自组网中动态源路由策略的路由发现和路由维护,并提出改进思路和今后研究的方向。     

应用频率-初速法测试推算单桩承载力须解决的几个关键问题

本文对当前频率 -初速法应用中存在的一些问题阐述了作者的看法并着重探讨桩振初速度V0的计算方法、W0 的正确单位、如何使桩 -土体系明显震动、怎样从激振曲线中突出及分离出桩振曲线 ,从而获得正确的桩振频率f0 和首波峰 -峰值Ad、动静对比系数 βv 的选取     

Transient Green’s Tensor for a Layered Solid Half-Space With Different Interface Conditions

Pulsed ultrasonic techniques can be and have been used to examine the interface conditions of a bonded structure. To provide a theoretical basis for such testing techniques we model the structure as a layer on top of a half-space, both of different elastic properties, with various interface bonding conditions. The exact dynamic Green’s tensor for such a structure is explicitly derived from the three-dimensional equations of motion. The final solution is a series. Each term of the series corresponds to a successive arrival of a “generalized ray” and each is a definite line integral along a fixed path which can be easily computed numerically. Willis’ method is used in the derivation. A new scheme of automatic generation of the arrivals and ray paths using combinatorial analysis, along with the summation of the corresponding products of reflection coefficients is presented. A FORTRAN code is developed for computation of the Green’s tensor when both the source and the detector are located on the top surface. The Green’s tensor is then used to simulate displacements due to pulsed ultrasonic point sources of known time waveform. Results show that the interface bonding conditions have a great influence on the transient displacements. For example, when the interface bonding conditions vary, some of the first few head waves and regular reflected rays change polarities and amplitudes. This phenomenon can be used to infer the quality of the interface bond of materials in ultrasonic nondestructive evaluation. In addition the results are useful in the study of acoustic microscopy probes, coatings, and geo-exploration.