某抽水蓄能电站地下厂房动力特性研究

抽水蓄能电站具有高水头、大容量、快转速的特点导致振动问题特别突出,强烈的振动会导致机组以及厂房薄弱结构部位发生破坏,影响电站的安全稳定运行。结合某在建抽水蓄能电站,分析了可能与厂房结构发生共振的振源,研究了边界条件、材料特性对结构自振特性的影响,结合粘弹性人工边界条件,分析了在机组动荷载作用下厂房各部位的动力响应规律。     

Modeling air flow in sanitary sewer systems: A review

Current designs of sanitary collection systems normally only consider the transport of wastewater without attention on the air movement in the sewer airspaces. Under anaerobic conditions, hydrogen sulfide (H₂S) can be generated in the liquid phase in sewer systems. H₂S is corrosive to concrete and steel structures and odorous or even toxic to human, which can cause corrosion and sewer odor issues. To develop a feasible sewer corrosion and odor control strategy, it is necessary to understand the mechanisms of air flow in sewer systems for developing practical tools to predict and control the air flow. This paper comprehensively reviewed previous efforts on modeling the air flow in sewer systems and provided recommendations on predicting the air flow for engineering applications. The air flow in a single pipe was firstly reviewed followed by the air flow in sewer structures as well as air flow models in sewer networks. Some other considerations such as temperature driven flow, transient water flow, and wind effect were also reviewed. The knowledge gaps were then identified, and recommendations on the further studies were provided.     

Comparison of infiltration models to describe infiltration characteristics of bioretention

Bioretention is one of low-impact development measures, which widely used not only because it can reduce stormwater runoff total volume, decrease peak flow rate and delay peak flow time, but also can remove the runoff pollutants. Infiltration is an important hydrological process for bioretention to evaluate its runoff total volume reduction and pollutants removal. So, it is important to find an optimal infiltration model that can well describe the infiltration performance of bioretention. The Horton, Philip and Kostiakov infiltration models were selected to compare their accuracy when using for describe the infiltration characteristics of bioretention, and the errors between the different models simulate results and experiment results were assessed via the maximum absolute error (MAE), bias and coefficient of determination (R²). The experimental results showed that Horton model is fitting well and flexible under different experiment conditions, especially when the hydraulic head was 10 cm, with MAE of 0.50–0.81 cm/h, bias of 0.1–0.23 cm/h and R² of 0.98–0.99. R² of the Philip and Kostiakov models were all over than 0.87 at the initial infiltration period, but the model fitting accuracy decreased significantly with infiltration time elapse. Furthermore, the total runoff volume capture ratio and emptying time were advanced used to evaluate the flexibility of Horton model, and the Nash-Sutcliffe efficiency coefficients of them were over than 0.61 and 0.58, respectively. Therefore, the Horton model can be optimal selected to describe the infiltration process of bioretention and for its hydrological evaluation.     

岩石高边坡稳定性并行计算及其应用

在高地震烈度区的岩石高边坡抗震安全评价需要大规模数值计算,而现有商业软件无法有效解决这类复杂的工程问题,因此,本文开发了解决岩石高边坡接触稳定性问题的对等架构并行计算程序,并应用于泰山公司抽水蓄能电站上水库左岸边坡的静力和动力稳定性评价。在数值建模过程中,将岩石边坡滑块体、地质结构面、库水作用以及近场地基作为岩石高边坡动力接触系统。在稳定性安全评价中结合了有限元法、极限平衡法和接触算法,考虑影响高边坡稳定性的多种复杂因素,通过计算特定滑动面的安全系数或安全系数时程,基于现行水电工程水工建筑物抗震设计规范,完成了岩石高边坡稳定性评价,回避了求解复杂岩体材料非线性的问题。计算结果显示,所开发的程序具有较高的并行计算效率,对解决复杂岩石高边坡稳定问题具有显著的优势。     

基于统一硬化参量的海洋K0固结土动力本构模型

为方便海洋工程中桩土相互作用计算,根据海洋K₀固结土体特性,对现有相关土体本构模型进行简化。在修正剑桥模型的基础上,基于热力学理论,选用耗散功作为硬化参量,结合原状土体的固结属性,推导了适用于黏土与砂土的统一硬化模型。在此基础上,通过采用旋转硬化与等向硬化相结合的硬化理论来表征K₀固结土在循环荷载作用下的硬化规律,同时引入屈服面收缩参数Θ来描述循环荷载加载过程中土体屈服面的演化特性,进而建立了循环荷载下海洋K₀固结土体统一硬化模型。为验证本文提出的本构模型的合理性,开展了2个案例的对比研究,研究结果表明:新提出的统一硬化模型的计算值与实测值吻合,选用的计算参数少且物理意义明确。     

DEM分辨率对山洪淹没模拟影响

DEM是表征地形状况的重要指标,在山洪淹没模拟中起着重要作用。以2016年7月19日发生在河北省石家庄市井陉县西部山区的特大暴雨山洪事件为研究对象,利用HEC-HMS水文模型和FLO-2D水动力模型,设置5种DEM分辨率方案(30、20、15、10、5 m),从淹没范围和淹没水深两方面分析了DEM分辨率对山洪淹没模拟的影响,并从模型运行时间角度对其运行效率进行了评估。研究表明:DEM分辨率越高,则淹没范围越小,平均淹没水深越大,即模型模拟精度越高,山洪事件的淹没范围及水深越接近于实际调查情况(DEM分辨率为30和5 m时,淹没范围及淹没深度的模拟精度分别为0.56和0.41、0.76和0.79);随着DEM分辨率的提高,尤其从10 m提高至5 m时,模拟结果差异减少,模拟精度的增幅也减小,淹没范围和水深的精度增幅分别为2.70%和3.94%;DEM分辨率越高,则模型运行时间越长,模型运行效率越低,5 m DEM方案下的运行时间为30 m DEM方案的700倍。综合考虑模拟精度及模拟时间,10 m分辨率的DEM对山洪淹没模拟、风险评估及预警预报等更为适用。     

基于CMIP5的中国西北地区暖湿化演变研究

为了解中国西北地区历史与未来时期的气候演变趋势,以CMFD再分析数据集及CMIP5全球气候模式输出数据为基础,从时空维度详细分析了西北地区历史气候的演变特征并对区域未来气候发展进行了预估。结果表明：1979-2018年西北地区的气温、降水量以及近地面空气比湿均呈现出明显的增加趋势,且未来极有可能继续增加;此外,降水量在年内的分配过程越趋均匀化,且降水结构在2001年左右发生了较大突变。整体来看,西北地区的历史气候演变显示出高度的暖湿化倾向。未来情景下,西北地区的气候将继续朝暖湿化方向发展,同时降水量的年内分配不均匀性也将进一步减小,且在RCP8.5排放情景下表现的更为突出。本研究可为西北地区气候变化的影响评估提供参考,同时也为水利、农业、气象和生态等部门的决策提供科学依据。     

黄河干流白银市水川段水面线计算方法对比分析

为克服能量方程逐段试算方法在河道水面线计算上存在的不足与局限,本文以黄河干流白银市水川段为例,采用二维水动力数值计算模型,对4种洪水频率工况下黄河干流白银市段的水面线高程进行计算,并将二维数值计算结果与能量方程计算结果进行复核和评价。经计算可知两种计算方法在计算结果上存在偏差,能量方程在河道水面线计算上是一种近似成果,而二维数值计算能够更加真实反映河道的实际情况,因此在水面线计算时推荐二维数值计算方法。     

水源涵养内涵及估算方法综述

水源涵养和生态系统过程与人类生产生活紧密相关,深入研究水源涵养对维持生态系统健康和人类社会可持续发展至关重要,对促进人与水和谐共生具有指导意义。随着对水源涵养研究与应用的深入,水源涵养内涵逐渐丰富,评估方法愈加多样,但以往的研究中水源涵养定义模糊,缺乏对各种评估方法的综合性对比分析,因此急需明确界定水源涵养内涵,分析各种估算方法的适用性。采用文献分析法系统梳理水源涵养研究历程,将其划分为认识与萌芽期、理论发展期、定量计算和模型综合评估等4个阶段;从定义、水量与功能等3个方面明确界定水源涵养内涵,从原理、时空尺度、适用范围及优缺点方面对已有水源涵养量估算方法进行对比和分析,并展望水源涵养研究的未来发展方向。     

基于关键闸坝优选的区域水网水量调控

为实现区域水网水量的高效调控,从水量、水生态、水质和闸坝管理等4个方面构建包含10个指标的闸坝优选评价指标体系,以廊坊市凤河-永定河区域水网为研究对象,计算区域内32座闸坝的综合关键指数并给出影响程度排序,采用水动力数学模型验证关键闸坝选取的合理性。结果表明：优选出的永丰闸和东张务闸是区域水网的关键闸坝,通过调节这两座闸坝的开度即可满足区域水网的生态需水和防洪排涝调度目标,保持区域水网较优的水力连通能力,提高区域水网水量调控效率。