酒泉盆地青西油田快速钻井技术

酒泉盆地青西地区油层储藏深 ,地层可钻性差 ,钻井过程中存在机械钻速低、井斜不易控制、刺断钻具频繁等问题。为此 ,在近年的钻井实践中 ,采取了优化钻具组合、优选钻头、应用 PDC钻头、强化钻具管理等措施 ,使该区块的钻井速度不断提高 ,钻井周期缩短 ,钻头用量减少 ,从而形成了一套适合该区块的快速钻井技术。     

葡北地区快速钻井技术

介绍了葡北地区地质构造及分层特征 ,分析了钻井难点 ,并给出了详细对策 ,从钻具组合、钻头优选、钻进参数优选、钻井液体系及安全技术措施等方面详细介绍了该区快速钻井技术。在葡北 4 - 11井和葡北 6- 1井的应用表明 ,该快速钻井技术能显著提高钻速 ,钻井周期明显缩短     

Viscoelasticity of oxidized starch/low methoxy pectin mixtures in the presence of glucose syrup

The structural properties of mixtures of pectin, oxidized starch and glucose syrup were investigated using small deformation dynamic oscillation. In the absence of added calcium, preparations of low methoxy pectin with glucose syrup formed viscous solutions, which remained crystal-free at subzero temperatures. Samples of oxidized starch and glucose syrup, on the other hand, exhibited solid-like behaviour because of the crystalline nature of the amylose-like helices. Mixtures of the two polysaccharides with the co-solute clearly showed phase inversion from liquid to solid-like behaviour with increasing amounts of starch in the formulation. The transformation was reflected in the textural properties of samples, which varied from thick solutions to firm gels. The viscoelasticity of the system was modified further by the introduction of high methoxy pectin. Preparations of high methoxy pectin and glucose syrup formed rubbery gels whose amorphous nature underwent a glass transition during cooling.     

DC-DC变换器突加负载时的动态性能研究

提出了一种能够有效改善DC-DC变换器动态性能的方案。该方案是在全桥电路基础上并联一单端正激变换电路，使变换器负载从10%轻载突加到100%满载时，其暂态过程小于1μs输出电压达到设计要求。文中对具体电路进行了详细分析，并通过仿真进行了验证。     

基于PLC电液比例控制的液力测功装置开发及其应用

本文介绍一种齿轮动态加载试验规范及技术要求，论述了运用电液比例控制技术所设计的液压加载系统原理及其使用效果，并简述由此构造的液力测功装置的原理与应用前景。     

Transient Green’s Tensor for a Layered Solid Half-Space With Different Interface Conditions

Pulsed ultrasonic techniques can be and have been used to examine the interface conditions of a bonded structure. To provide a theoretical basis for such testing techniques we model the structure as a layer on top of a half-space, both of different elastic properties, with various interface bonding conditions. The exact dynamic Green’s tensor for such a structure is explicitly derived from the three-dimensional equations of motion. The final solution is a series. Each term of the series corresponds to a successive arrival of a “generalized ray” and each is a definite line integral along a fixed path which can be easily computed numerically. Willis’ method is used in the derivation. A new scheme of automatic generation of the arrivals and ray paths using combinatorial analysis, along with the summation of the corresponding products of reflection coefficients is presented. A FORTRAN code is developed for computation of the Green’s tensor when both the source and the detector are located on the top surface. The Green’s tensor is then used to simulate displacements due to pulsed ultrasonic point sources of known time waveform. Results show that the interface bonding conditions have a great influence on the transient displacements. For example, when the interface bonding conditions vary, some of the first few head waves and regular reflected rays change polarities and amplitudes. This phenomenon can be used to infer the quality of the interface bond of materials in ultrasonic nondestructive evaluation. In addition the results are useful in the study of acoustic microscopy probes, coatings, and geo-exploration.     

动态光散射法研究海藻酸钠凝胶松弛行为

在前文的基础上，用相关函数轮廓分析的方法剖析了运动模型模式的复杂性。通过海藻酸钠水溶液在０．１ｍｏｌ／ＬＣａＣｌ２水溶液透析凝胶化过程中交联网络的松弛时间谱表明它不是单一的峰，有两上特征运动模式，并随透析向更慢的运动模式发展，这很慢的运动模式估计与区域的结构的生成有关。     

热释电系数的测量方法

描述热释电系数的两种测量方法。其一为电荷积分法，测试系统简单，测量数据准确，且能满足零电场条件下的测量。其二为动态电流法，采用调制热源技术，研究在特定温度条件下热释电材料的动态热释电响应。     

风机叶轮的现场平衡方法

介绍了利用简单方法，解决风机叶轮现场静、动平衡的问题。方法快速、准确、实用。     

Absorption of materials by or through the living skin

The skin comes into contact with a large range of materials either deliberately or inadvertently. It should be possible to predict the exact transport rates of these materials through the skin as a function of the physicochemical properties of the different compounds. With this sort of knowledge it is possible to predict the exact disposition of compounds and use this in the formulation of new products both in the pharmaceutical and cosmetic field. The information will also be useful from the standpoint of skin toxicology and environmental health. In order to be able to predict this complex process it is necessary to split the overall transport into different component parts. This article will identify these components and provide illustrations. The major areas discussed will be barrier function of the skin, the release properties of different topical formulations and how these may be monitored. Novel means of enhancing the penetration of drugs will be discussed and how some additives that are incorporated into formulations will perhaps alter the barrier function of skin. A mathematical model describing skin penetration has been developed and its use in predicting blood levels will be described. This model has been tested both in animal experiments and in limited human studies and its relevance to these situations will be highlighted.
Absorption cutanée et transcutanée in vivo