水煤浆燃烧技术及其发展

分析了水煤浆雾化燃烧的技术状况、应用方向和存在问题，介绍了水煤浆流化—悬浮高效洁净燃烧新技术及其优点，结合实践应用情况，分析了发展水煤浆流化—悬浮燃烧技术的意义和应用前景。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。     

目标RCS动态数据的分布特征研究

复杂目标在不同视向的RCS分布特征是不同的，传统模型对此都没有给出详细的结果。文中以某歼击机和直升机为对象，应用X^2。分布、对数正态分布和瑞利分布模型，以及Kolmogomv拟合优度检验方法，研究其RCS动态测量数据的统计分布特征，得到了在一定显著性水平下，两种目标在不同视向角下对三种模型的拟合效果，同时得到应用X^2。分布拟合时模型半自由度随视向角的分布情况。在显著性水平为0．05时，对于在较短时间内录得的复杂目标动态RCS数据，应用X^2分布可以取得较好的拟合效果。文中结果精确地描述了目标RCS的起伏特征，能够为目标回波的精确模拟与检测提供可靠的依据。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

A three-dimensional FE analysis of large deformations for impact loadings using tetrahedral elements

 A three-dimensional dynamic program for the anaysis of large deformations in contact-penetration problems is developed using the finite element Lagrangian method with explicit time integration. By incorporating a tetrahedral element, which allows a single-point integration without a special hourglass control scheme, this program can be more effective to the present problem. The position code algorithm is used to search contact surface. Eroding surfaces are also considered. The defense node algorithm was slightly modified for the calculation of contact forces. A study of obliquity effects on metallic plate perforation and ricochet processes in thin plates impacted by a sphere was conducted. It is well simulated that on separation of two parts of the sphere, the portion still within the crater tends to perforate, while the portion in contact with the plate surface ricochets. This deformation pattern is observed in experiments, especially at high obliquities. A long rod that impacts an oblique steel plate at high impact velocity was also simulated in order to study the dynamics of the rod caused by the three dimensional asymmetric contact. The agreement between simulated and experimental results is quite good. Fracture phenomena occuring at high obliquity deserves further investigations. Received: 20 February 2002 / Accepted: 20 September 2002     

Heavy Metals Bioremediation from Polluted Water by Glass-Ceramic Materials

The objective of this research was to study the removal of cadmium and lead from an aqueous solution through a biological treatment. For this purpose a glass-ceramic material was manufactured from industrial and urban wastes. Biofilms of microorganisms found in wastewater were developed on its surface, and continuous tests were conducted in the presence and absence of the biofilm to analyze the glass-ceramic's ability to remove the heavy metals from an aqueous environment. The results suggest that this bioremediation process, developed on an industrial scale, could represent an alternative to the chemical processes currently used.     

Analysis and simulations of vibrations of a beam with a slider

A model for vibrations of a beam with a slider is derived, analysed and numerically simulated. It describes a viscoelastic beam that is clamped at one end to a vibrating device, while the other end moves between two stops attached to a slider. The contact is described by the normal compliance or by the Signorini conditions. The existence of weak solutions is established using the theory of set-valued pseudomonotone operators. The model is discretized using fourth-order spatial discretization, the solutions are numerically simulated and their results presented. The dynamics of the vibrations are depicted and so are the noise characteristics of the system.     

正确选择气顶油藏高效开发模式

通过对不同类型气顶油藏的油气水分布特征及气顶和边水能量的研究分析，计算水侵量与边水体积及合理的弹性产率。提出适合气顶油藏特点的开发模式是先开采油区后开采气顶，并以唐家河油田港深18—2断块为例，证明采用该模式可以高效开发气顶油藏。图3表1参6     

一类连续模糊动态系统控制方法在Furuta摆中的应用

为了研究Furuta摆在倒立点附近的稳定控制问题，采用基于T-S模糊模型的一类连续模糊动态系统控制方法，首次进行Furuta摆的模糊状态空间建模，并采用模糊切换的思想，设计了Furuta摆在倒立点附近的稳定控制器，进而分析了系统稳定性。与已有的方法相比，该方法的优点是稳定区域大、调节时间短。数字仿真结果验证了方法的有效性。     

支流影响下的水库水温预测模型

采用宽度平均的立面二维水温模型,通过分析支流和主库之间的相互影响,提出了支流与主库耦合的简化方法,建立了考虑支流影响的水库水温模型。在考虑有无支流影响的条件下,对水库水温分布、水库下泄水温和坝前垂向水温分布均作了比较,结果表明支流对水库水温分布有一定的影响,所建立支流与主库耦合的立面二维水温模型能够较好地反映存在支流影响的水库水温分布,预测水库水温分布比较合理。