起落架落震试验飞机机轮三向冲击位移的动态测量

为了研究飞机起落架受冲击载荷时的功量吸收状况，须在起落架落震试验中，对飞机着陆瞬间起落架机轮在空间三个方向上冲击位移的动态变化量进行测量。为此，本文设计了四自由度空间定位装置，并使其与计算机连接，实现了落震试验过程中，起落架在高速冲击状态下机轮三向位移的有效测量与记录。     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

二滩电厂双缸液压启闭机原理及故障分析

二滩电厂表孔采用弧形门,启闭形式为双缸液压启闭机.自投入运行以来,运行状况良好.汛期启闭方式已由原来的现地手动操作过渡到远方控制自动启闭.在闸门起落的过程中,由于工况的不同,两缸会出现不同步现象,因此设计中考虑了纠偏回路.本文简单介绍了二滩电厂表孔液压启闭机的原理和故障情况.     

锚索测力计有关应用问题的探讨

通过分析锚索测力计因受力状态不同而带来的系统误差,提出了测力计实测锚固力的修正方法及部分测力计传感器失效后延续锚固力测值的计算方法.     

As Hangs the Flexible Line: Equilibrium of Masonry Arches

In 1675, English scientist Robert Hooke discovered “the true... ...manner of arches for building,” which he summarized with a single phrase: “As hangs the flexible line, so but inverted will stand the rigid arch.” In the centuries that followed, Hooke’s simple idea has been used to understand and design numerous important works. Recent research at MIT on the interactive analysis of structural forces provides new graphical tools for the understanding of arch behavior, which are useful for relating the forces and geometry of masonry structures. The key mathematical principle is the use of graphical analysis to determine possible equilibrium states.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

小眼井最优水力学设计及分析

在充分考虑小眼井钻井特点和合理确定环空压耗的基础上，将喷射钻井理论和环空携岩理论有机结合起来，导出了在两种工作方式下优化设计小眼井钻井水力参数模型，并开发了应用软件。通过实例计算，提出了在小眼井最优水力学设计中采用最大水功率工作方式的重要性，并建议在大眼井的水力参数设计中考虑钻柱的偏心、旋转和钻杆接头对环空压耗的影响。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

太钢3#高炉重力除尘器大件吊装

太钢3#高炉大修改造是集团公司重点外部工程项目之一，工程量大，工期紧，施工场地狭小，而质量要求较高。如何采取科学、经济的设备吊装方案，对整个项目经济指标的实现，意义重大。文章详细介绍了太钢3#高炉重力除尘器大件整体吊装方案。通过实际采用，取得良好的经济效果。