液压胀形轧辊油槽深度的确定

对液压胀形轧辊（即国外的ＶＣ轧辊）辊套热装后的弹性变形进行了有限元分析，给出了确定油槽最小深度的计算公式。本文的有限元计算结果与实验结果吻合，某些结论可为液压胀形轧辊的结构设计提供理论依据。     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

弹性筛管防砂技术

弹性筛管防砂技术是根据稠油油藏高轮次吞吐和蒸汽驱井防砂生产需要而研制的筛管防砂新技术。进行了筛管结构优化、加厚过滤单元外罩设计、固定方式研究、弹性过滤材料筛选、防腐实验研究等。室内试验表明，筛管的过流能力在900cm^2／m以上、渗透率在100μm^2以上、筛管抗内、外压强度达到20MPa、防砂粒径在0.1mm以上、耐温350℃、pH值在3～12之间不被腐蚀。现场试验证明，该技术防砂和抗堵塞性能好，防砂有效期长，地层适应性强，施工简便，防砂生产效果明显，具有良好的应用前景。     

钻杆防磨技术的现状和发展

在深井超深井勘探过程中，由于径向力、涡动、横向振动等因素的存在，随着钻井时间的增长，钻柱作用于套管内壁的侧向力增大，导致套管磨损的问题越来越严重。介绍了近年来钻杆防磨技术的发展，主要从钻杆接头表面处理和钻杆保护器2方面来研究防磨减磨措施的现状和发展。     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。     

节理岩体的代表单元集合体模型及弹性参数预测

本文明确提出了节理岩体“代表单元集合体”的概念和模型，通过对节理岩体的“代表单元集合体”进行数值模拟，研究了节理岩体的“代表单元集合体”的变形特性，建立了节理岩体的弹性模型，提出了预测节理岩体宏观等效弹性参数的计算机模拟方法，并将其应用于岩体工程稳定性分析中。     

钢骨架塑料(PE)复合管的安装技术

钢骨架塑料复合管既有钢管的耐压又有塑料管的耐腐蚀性，且易于敷设，使用寿命长，本文结合实际施工中的应用。介绍其要点。     

轮式工程机械的行驶平稳性

根据振动理论建立了振动力学模型,并用等效刚度方法分析研究了弹性悬挂轮式工程机械行驶平稳性和振动特性。     

面向表面组装工艺技术的PCB焊盘设计

尽管电子设计类软件已相当先进和方便，而且更新速度也很快，但是仍然无法满足各个层次的设计人员的需求，特别是适合各种元素封装形式的焊盘设计库并不能让设计和制造者满意，为了在此方面对PCB设计有所帮助，从印制电路板焊盘的设计方法入手，针对表面组装工艺技术特点，分析了PCB焊盘对PCA可靠性的影响因素，并根据相关的质量要求提出了较为简便的设计方案。