Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

Fabrication of sharp silicon tips employing anisotropic wet etching and reactive ion etching

We developed a process to obtain sharper silicon tips by employing anisotropic etching in a KOH solution followed by SF₆ plasma etch. The tips were further sharpened using the established thermal oxidation technique to decrease the cone angle and, therefore, obtain smaller curvature radii. We have analyzed the impact of such changes in geometry on a figure of merit associated with the field emission characteristics. An increase in the figure of merit by a factor of three was found in relation to the tips before sharpening.     

Ti-silicalite as catalyst for gas-phase ammoximation of cyclohexanone with molecular oxygen

The catalyst behaviour of titanium silicalite, which was found the most active and selective catalyst for liquid-phase ammoximation of cyclohexanone to the corresponding oxime with hydrogen peroxide, was investigated in the gas-phase ammoximation with molecular oxygen in and compared with those of pure silicalite and samples of vanadium and chromium silicalites. The results showed that Ti-silicalite is a selective catalyst not only in the reaction with hydrogen peroxide but also in the reaction with molecular oxygen. However, a big limitation was found in the poor activity of the silicalites which do not allow to reach high oxime yields.     

Phase Composition of Oxide Scales during Reheating in Hot Rolling of Low Carbon Steel

Low carbon steel was oxidized over the temperature range 1000‐1250°C in O₂‐CO₂‐H₂O‐N₂, O₂‐H₂O‐N₂, and O₂‐CO₂‐N₂ gas mixtures. Oxidation times were 12‐120 min. and the scales were 50‐2000 μm thick. The variations of these parameters were chosen to elucidate the phase composition of oxide scales under conditions similar to those of reheating furnaces in hot strip mills, using either thin slab casting or conventional casting and rolling technology. Two types of scales have been observed which are influenced by the furnace atmosphere, oxidation time, and temperature. The first type is a crystalline scale with an irregular outer surface, composed mostly of wustite (FeO), and a negligible amount of magnetite (Fe₃O₄). The second type is the classical three‐layer scale, composed of wustite (FeO), magnetite (Fe₃O₄), and hematite (Fe₂O₃). In general, the experiments showed that an increase in oxidation time decreased the percentage of wustite while the percentages of magnetite and hematite increased. A rise in oxygen concentration in the gas mixture increased the percentages of magnetite and hematite, confirming earlier experimental findings. In water vapour‐free atmospheres O₂‐CO₂‐N₂, the oxide scales had a low percentage of wustite, and high percentage of magnetite and hematite. Carbon dioxide showed a small influence at 1100°C, and a negligible one at 1250°C.     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

Effect of temperature on methyl radical generation over Sr/La2O3 catalysts

The role of gas phase CH₃ radicals in the oxidative coupling of CH₄ over 1 wt% Sr/La₂O₃ is supported by the observations that (i) this is a very effective catalyst for the generation of CH₃ · radicals and (ii) the concentration of CH₃ · radicals increases with temperature over the range of 450 °C–800 °C.     

Fractionation and characterisation for antioxidant activity of hydrolysed whey protein

Whey protein isolate (WPI) was hydrolysed for 1 h using Alcalase, Protamex and Flavourzyme. Native WPI, hydrolysed WPI and two commercial WPI hydrolysates were subjected to fractionation by size exclusion chromatography. Antioxidant activity of WPI fractions was measured with a liposome‐oxidising system (50 µM FeCl₃/0.1 µM ascorbate, pH 7.0). Lipid oxidation was measured as thiobarbituric acid‐reactive substances (TBARS). Gel electrophoresis and amino acid analysis were run to identify the peptide composition. The influence of amino acid composition on antioxidant activity was evaluated using multivariate analysis methods (correlation analysis, principal component analysis, multiple linear regression and discriminant analysis). TBARS assays indicated the presence of antioxidant activity in all protein fractions, including non‐hydrolysed WPI. For native and hydrolysed WPI samples the first fraction (> 45 kDa) showed a higher TBARS inhibition effect (24–27%) when compared with lower‐molecular‐weight fractions and hydrolysate mixtures. In contrast, for commercial WPI hydrolysates a higher inhibitory effect was found in most of the lower‐molecular‐weight fractions (30–55%). The ability of WPI fractions to delay lipid oxidation was found to be related to the prevalence of histidine and hydrophobic amino acids. Copyright © 2004 Society of Chemical Industry     

La-OMS-2催化剂催化甲苯氧化制苯甲醛

合成了氧化锰八面体(OMS-2)分子筛,采用离子交换法和浸渍法制备了稀土金属La改性的OMS-2分子筛(La-OMS-2)催化剂,并用于甲苯液相选择性氧化制苯甲醛,考察了催化剂用量、反应温度、反应时间、氧气流量及溶剂种类对甲苯转化率和苯甲醛选择性的影响,对La-OMS-2催化剂进行了X射线衍射表征和BET比表面积测定。实验结果表明,离子交换法制备的La-OMS-2-A催化剂的活性高于浸渍法制备的La-OMS-2-B催化剂,在甲苯0.1mol、溶剂冰乙酸10mL、氧气流量60mL/min、La-OMS-2-A催化剂用量0.10g、反应温度353K、反应时间1.0h的条件下,甲苯转化率达61%,苯甲醛收率为56%。加入La对OMS-2分子筛中的MnO晶格结构产生了影响,提高了苯甲醛的收率。     

Optimization of anodic oxidation and Cu–Cr oxide catalyst preparation on structured aluminum plates processed by electro discharge machining

This paper describes the optimization of three processes applied in fabrication of a microstructured reactor for complete oxidation of volatile organic compounds. The first process involves the optimization of the electro discharge machining (EDM) method to produce a set of microchannels with a high length to diameter ratio of 100, with a standard deviation from the average diameter below 0.2%, and with a surface roughness not higher than 2.0 μm. To satisfy these criteria, fabrication of microchannels must be carried out with two machining passes in the Al51st alloy. Then, the effect of several parameters on the anodization current efficiency with respect to oxide formation was studied. The best process conditions to get a 30 μm porous alumina layer in a 0.4 M oxalic acid electrolyte, were found to be a temperature of 1 °C, an anodic current density of 5 mA/cm², and 23 h oxidation time. At last, the resulting coatings were impregnated with an aqueous solution of copper dichromate followed by drying and calcination at 450 °C to produce active catalysts. The effect of a copper dichromate concentration, number of impregnation cycles (1 or 2), and different after-treatments on catalytic activity and stability in complete oxidation of n-butane were studied. The catalytic activity of the obtained coatings is superior to that of alumina supported pelletized catalysts even at much lower loadings of active metals.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.