An Investigation of Milk Powders Produced by a Laboratory-Scale Spray Dryer

A mini spray dryer has been used to investigate morphological changes that occur to milk particles during the spray drying process. We have found that the mini spray dryer is ideal for such investigations, because phenomena such as skin and vacuole formation in particles can be analyzed without the added complication of particle agglomeration, which only occurs in much larger spray dryers where particle number concentrations are higher. We have confirmed observations made by various researchers that the bulk density of spray-dried milk powder is greatly affected by the drying temperature, due to the strong influence of the latter on the porosity of the particles. In addition, we have attempted to explain observations made by various workers that fat accumulates preferentially at the surface of a particle during drying by postulating that fluid fat is transported towards the surface, via a network of cracks and pores, by the development of a vacuole overpressure which is also responsible for the inflation of the particle. Finally, we have shown that milk powders can be spray dried a second time, by reconstitution with water, with no change to the thermodynamic characteristics of the resultant powder. Thus, milk concentrates for spray drying research can be prepared from already-spray-dried milk powders rather than using the more arduous evaporation method to concentrate unprocessed milk.     

Scanning electron microscope electron detector with a radial type discrete dynode electron multiplier

A discrete dynode electron multiplier with radial flux of electrons was built and tested in the range of low‐voltage scanning electron microscopy as a backscattered electron detector of topographic contrast. The multiplier collects backscattered electron emitted in a specific range of take‐off angles and over the whole azimuth angular range enabling large solid collection angle. Multipliers with different dynode shapes were studied theoretically with the use of the software for particle optics and three assemblies were built and tested experimentally. The gain estimation, assessment of the type of detected electrons (secondary electron or backscattered electron), imaging the spatial collection efficiency and signal‐to‐noise measurements were performed.     

奥里油在电力工业的应用及环保处理

委内瑞拉富藏奥里油约469亿t，中国政府与委内瑞拉政府签订了合作生产和供应每年650万t奥里油的合作协议。介绍了奥里油的特性和在全球以及中国的应用情况，分析了奥里油燃烧发电带来的特殊的环保问题和处理方法。     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Growth structure investigation of MgF2 and NdF3 films grown by molecular beam deposition on CaF2(111) substrates

The growth structure of MgF₂ and NdF₃ films grown on polished CaF₂(111) substrates deposited by molecular beam deposition has been investigated using transmission electron microscopy (TEM) of microfractographical and surface replications as well as cross-sectional TEM, atomic force microscopy, packing density, and absorption measurements. It has been shown that by taking advantage of ultrahigh vacuum environments and a special stratification property of MgF₂ and NdF₃ films, the preparation of nanocrystalline films of high packing density and low optical absorption is possible at a substrate temperature of 425 K.     

Automated fluorimetry in quality control of pasteurized and ultra-high temperature-treated starch soup

Automated monitoring of the microbiological quality of heat-processed foods by the resazurin reduction test was applied to microtitration plate incubator-fluorimeter technology. The appearance and disappearance of the fluorescing peak of resorufin was monitored on microtitration trays. Pasteurized or ultra-high temperature-treated starch-based soup was used as the model food system. Bacillus subtilis spores (ultra-high temperature treatment) and vegetative cells of Enterococcus faecalis (pasteurization) were inoculated into the soup before the heat treatment at levels which resulted in some survival. The timing of appearance of maximum fluorescence correlated with the number of bacteria in pre-incubated samples. Automated resazurin-reduction fluorimetry was compared with conventional plating, turbidometry and microcolony count by the direct epifluorescent filter technique. The results of the resazurin test correlated well with those of all the other methods tested. Fluorimetry had the advantage that the results could be read within 1–5h and the reproducibility was superior to the other methods.     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.     

Electrooptic studies on polymer‐dispersed liquid‐crystal composite films. III. Poly(methyl methacrylate‐co‐butyl acrylate)/E7 and poly(methyl methacrylate‐co‐butyl acrylate)/E8 composites

Composite films composed of poly(methyl methacrylate‐co‐butyl acrylate) (PMMABA) and nematic‐type liquid crystals E7 and E8 (commercial products from E. Merck, Darmstadt, Germany) were prepared through solvent casting in chloroform. The morphology and electrooptic responses were studied. Scanning electron microscopy observations showed that the liquid‐crystal phase (E7 or E8), as larger, elongated, interconnected cavities, was continuously embedded in a spongelike PMMABA matrix. At a specific level of the liquid‐crystal (E7 or E8) loading (30/70 wt %), the effects of the voltage, temperature, and frequency of an applied alternating‐current electric field on the transmittance of the composite films were measured with a He–Ne laser (wavelength = 632.8 nm). The results were interpreted in terms of the aggregation structure, interfacial interaction, and solubility of the liquid crystal in the matrix polymer. The results indicated that, under these experimental conditions, the output could be controlled to a desired level by the selection of suitable liquid crystals to prepare polymer‐dispersed liquid‐crystal, electrooptic, active composite films with a response time of the order of only milliseconds or less. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008