Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

VERIFICATION AND COMPARISON OF FORMULAS FOR BED LOAD TRANSPORT

1 .　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｂｅｄｌｏａｄｔｒａｎｓｐｏｒｔｈａｓｂｅｅｎｅｘｔｅｎｓｉｖｅｌｙｓｔｕｄｉｅｄｉｎｔｈｅｐａｓｔｆｅｗｄｅｃａｄｅｓａｎｄｍａｎｙｆｏｒｍｕｌａｓｆｏｒｐｒｅｄｉｃｔｉｎｇｂｅｄｌｏａｄｔｒａｎｓｐｏｒｔｒａｔｅｈａｖｅｂｅｅｎｐｒｅｓｅｎｔｅｄ(Ｅｉｎｓｔｅｉｎ 1950 ;Ｍｅｙｅｒ Ｐｅｔｅｒ 194 8;Ｂａｇｎｏｌｄ 1973;Ｅｎｇｅｌｕｎｄ 1976;Ｙａｌｉｎ 1972 ;Ｓａｍａｇａ 1986;ａｎｄＫａｒｉｍ 1998) .Ｗｈｅｎａｐｐｌｉｅｄｔｏｓｔｒｅａｍｓｗｉｔｈｐａｒｔｉａｌ…     

迫零对Turbo码的性能影响

从距离谱的角度对迫零在Turbo码中的作用进行了理论分析。通过仿真，研究了迫零对Turbo码性能的影响。仿真结果表明，Turbo码编码器迫零处理有助于改善Turbo码的性能。     

钴—60远距离治疗源的活度

本文简述了钴-60远距离治疗源的照射量率测量、活度计算及其误差分析。结果的合成不确定度分别小于±4%和±10%。同时,它适用于其它高活度钴-60密封源.     

酒泉盆地青西油田快速钻井技术

酒泉盆地青西地区油层储藏深 ,地层可钻性差 ,钻井过程中存在机械钻速低、井斜不易控制、刺断钻具频繁等问题。为此 ,在近年的钻井实践中 ,采取了优化钻具组合、优选钻头、应用 PDC钻头、强化钻具管理等措施 ,使该区块的钻井速度不断提高 ,钻井周期缩短 ,钻头用量减少 ,从而形成了一套适合该区块的快速钻井技术。     

葡北地区快速钻井技术

介绍了葡北地区地质构造及分层特征 ,分析了钻井难点 ,并给出了详细对策 ,从钻具组合、钻头优选、钻进参数优选、钻井液体系及安全技术措施等方面详细介绍了该区快速钻井技术。在葡北 4 - 11井和葡北 6- 1井的应用表明 ,该快速钻井技术能显著提高钻速 ,钻井周期明显缩短     

混合冷媒气液相充注对冷媒成分的影响

R40 7C、R5 0 7A、R40 4A和R410A混合冷媒按气、液相方式进行充注时 ,冷媒容器内的冷媒成分会或多或少地随着冷媒容器移充填率的变化而变化。因此 ,本文建议充注任何混合冷媒时 ,都应该采用液相方式进行充注 ,同时为了将冷媒成分变化控制在 2 %以内 ,R40 7C冷媒容器中最后的 10 %冷媒剩余量不应再进行充注 ,R5 0 7A、R40 4A和R410A冷媒容器中的最后冷媒剩余量可控制在 5 %。     

合成孔径雷达图像的恒虚警率目标检测

目的　对合成孔径雷达 (SAR)图像实施恒虚警率 (CFAR)目标检测 .方法　利用 K-Gamma和Weibull分布的杂波模型分别对海面和陆地的人造目标实施检测 ;同时 ,对不同杂波背景下 CFAR检测方法进行比较 .结果与结论　通过检测结果的比较 ,证实了 K-Gamma分布和 Weibull分布分别适合于海面和陆地杂波背景下的目标检测 ;在非均匀杂波背景中 ,有序统计量 (OS)较单元平均 (CA)方法具有优越性     

辽宁省2000年夏季干旱分析

本文针对辽宁省2000年发生的干旱,从大气环流、气候、降水、径流、水资源量等方面,较系统地阐述了各因素的发展规律、特点及物理成因。采用降水指标、径流指标、受旱率进行干旱程度分析。评价出辽宁省2000年干旱为特大干旱。