Crystal-field engineering of ultrabroadband mid-infrared emission in Co2+-doped nano-chalcogenide glass composites

Tunable and ultrabroadband mid-infrared (MIR) emissions in the range of 2.5–4.5 μm are firstly reported from Co²⁺-doped nano-chalcogenide (ChG) glass composites. The composites embedded with a variety of binary (ZnS, CdS, ZnSe) and ternary (ZnCdS, ZnSSe) ChG nanocrystals (NCs) can be readily obtained by a simple one-step thermal annealing method. They are highly transparent in the near- and mid-infrared wavelength region. Low-cost and commercially available Er³⁺-doped fiber lasers can be used as the excitation source. By crystal-field engineering of the embedded NCs through cation- or anion-substitution, the emission properties of Co²⁺ including its emission peak wavelength and bandwidth can be tailored in a broad spectral range. The phenomena can be accounted for by crystal-field theory. Such nano-ChG composites, perfectly filling the 3–4 μm spectral gap between the oscillations of Cr²⁺ and Fe²⁺ doped IIVI ChG crystals, may find important MIR photonic applications (e.g., gas sensing), or can be used directly as an efficient pump source for Fe²⁺: IIVI crystals which are suffering from lack of pump sources.     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

Effects of sintering in a high magnetic field on properties of vitrified bond and vitrified CBN composites

Vitrified bond CBN grinding wheels are being widely used due to their superior performance. Also, advantages of vitrified grinding wheels are high elastic modulus, stable chemical property, and low thermal expansion coefficient. Brittleness and low strength are key factors restricting the development of vitrified bond CBN grinding wheels. In this paper, the sintering in a high magnetic field was innovatively introduced into the manufacturing of vitrified bond CBN grinding wheels, and the effects of sintering in a high magnetic field on properties on vitrified bond and vitrified CBN composites were systematically investigated. Vitrified bond was characterized using three-point bending, scanning electron microscopy, X-ray diffraction. It was observed that microstructure of vitrified bond could be changed, grain orientation could be controlled and average grain size could be decreased in a high magnetic field, while vitrified bond strength could be simultaneously improved. High quality vitrified bond could be obtained by appropriately adjusting the strength and direction of high magnetic field. Results demonstrated that vitrified bond properties were improved when the magnetic field strength was 6?T. In order to highlight the high magnetic field effect on the vitrified CBN composites, the ordinary CBN abrasives and nickel plated CBN abrasives were used respectively. Microstructures, bending strengths of vitrified CBN composites were compared in different high magnetic fields. When the magnetic field strength was appropriate (less than 6?T), the binding characteristic of vitrified bond CBN composites with nickel plated CBN abrasives was greatly improved. The highest bending strength value of vitrified CBN composites was 79.5?MPa in 6?T high magnetic field.     

Survey on Passivity Based Control of Induction Machine

Induction machines (IM) constitute a theoretically interesting and practically important class of nonlinear systems. They are frequently used as wind generators for their power/cost ratio. They are described by a fifth‐order nonlinear differential equation with two inputs and only three state variables available for measurement. The control task is further complicated by the fact that IM are subject to unknown (load) disturbances and the parameters can be of great uncertainty. One is then faced with the challenging problem of controlling a highly nonlinear system, with unknown time‐varying parameters, where the regulated output, besides being unmeasurable, is perturbed by an unknown additive signal. Passivity‐based control (PBC) is a well‐established structure‐preserving design methodology which has shown to be very powerful to design robust controllers for physical systems described by Euler‐Lagrange equations of motion. PBCs provide a natural procedure to "shape" the potential energy yielding controllers with a clear physical interpretation in terms of interconnection of the system with its environment and are robust vis á vis to unmodeled dissipative effects. One recent approach of PBC is the Interconnection and Damping Assignment Passivity‐Based Control (IDA‐PBC) which is a very useful technique to control nonlinear systems assigning a desired (Port‐Controlled Hamiltonian) structure to the closed‐loop. The aim of this paper is to give a survey on different PBC of IM. The originality of this work is that the author proves that the well known field oriented control of IM is a particular case of the IDA‐PBC with disturbance.     

Sequence-Dependent Nanofiber Structures of Phenylalanine and Isoleucine Tripeptides

The molecular design of short peptides to achieve a tailor-made functional architecture has attracted attention during the past decade but remains challenging as a result of insufficient understanding of the relationship between peptide sequence and assembled supramolecular structures. We report a hybrid-resolution model to computationally explore the sequence–structure relationship of self-assembly for tripeptides containing only phenylalanine and isoleucine. We found that all these tripeptides have a tendency to assemble into nanofibers composed of laterally associated filaments. Molecular arrangements within the assemblies are diverse and vary depending on the sequences. This structural diversity originates from (1) distinct conformations of peptide building blocks that lead to different surface geometries of the filaments and (2) unique sidechain arrangements at the filament interfaces for each sequence. Many conformations are available for tripeptides in solution, but only an extended β-strand and another resembling a right-handed turn are observed in assemblies. It was found that the sequence dependence of these conformations and the packing of resulting filaments are determined by multiple competing noncovalent forces, with hydrophobic interactions involving Phe being particularly important. The sequence pattern for each type of assembly conformation and packing has been identified. These results highlight the importance of the interplay between conformation, molecular packing, and sequences for determining detailed nanostructures of peptides and provide a detailed insight to support a more precise design of peptide-based nanomaterials.     

关于信息化测绘时代工程测量发展的思考

如今我国信息化技术全面发展，尤其对于工程测量工作领域来讲，不管是在工程建设和管理方面都产生不小的支撑引导效用。由此，笔者具体结合如今工程建设信息化测绘核心任何以及设备布置细节，进行结构整体安全管理周期和周边地理空间信息技术发展能效整理解析，试图将工程测量最新发展机遇和技术挑战问题处理完全。希望能够借此为日后一定时期范围内相关工程测量规划主体提供合理指导性建议内容，最终为我国各类工程事业可持续发展前景绽放奠定深刻适应基础。     

基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。