DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

金属配合物与核酸作用机理的理论计算

通过计算机模拟金属配合物与核酸作用机理,对其理论模型能量计算和结构优化。在不同的化学环境条件下得到不同的实验模拟结果,对真实的化学反应过程有重要的指导意义和参考意义。通过Gaussian03,Gauss View等软件的结合应用,分别应用于优化计算和理论建模,熟悉了对化学软件操作应用。     

Passive target detection and tracking from electromagnetic field measurements

This paper presents a novel approach to the localization of moving targets in a complex environment based on the measurement of the perturbations induced by the target presence on an independently‐generated time‐varying electromagnetic field. Field perturbations are measured via a set of sensors deployed over the domain of interest and used to detect and track a possible target by resorting to a particle Bernoulli filter (PBF). To comply with real‐time operation, the PBF works along with an artificial neural network (ANN) model of the environment trained offline via finite elements (FEs). The performance of the proposed algorithm is assessed via simulation experiments.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Zinc doped Fe2O3 for boosting Electrocatalytic Nitrogen Fixation to ammonia under mild conditions

Artificial nitrogen fixation is emerging as a promising approach for synthesis of ammonia at mild conditions. Inspired by biological nitrogen fixation based on bacteria containing iron, zinc doped Fe₂O₃ nanoparticles are proposed as an efficient and earth abundant electrocatalyst for converting N₂ to NH₃. In neutral media, it achieves a maximum Faradaic efficiency (FE) of 10.4% and a large NH₃ yield rate of 15.1 μg h^?1 mg^?1_cat. at ?0.5 V vs. reversible hydrogen electrode. This catalyst also exhibits excellent selectivity and stability. Theoretical calculations suggest the reaction follows the associative enzymatic mechanism and it has a barrier of as low as 0.68 eV.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。     

A comparison of transformation methods for evaluating two‐dimensional weakly singular integrals

Accurate numerical evaluation of integrals arising in the boundary element method is fundamental to achieving useful results via this solution technique. In this paper, a number of techniques are considered to evaluate the weakly singular integrals which arise in the solution of Laplace's equation in three dimensions and Poisson's equation in two dimensions. Both are two‐dimensional weakly singular integrals and are evaluated using (in a product fashion) methods which have recently been used for evaluating one‐dimensional weakly singular integrals arising in the boundary element method. The methods used are based on various polynomial transformations of conventional Gaussian quadrature points where the transformation polynomial has zero Jacobian at the singular point. Methods which split the region of integration into sub‐regions are considered as well as non‐splitting methods. In particular, the newly introduced and highly accurate generalized composite subtraction of singularity and non‐linear transformation approach (GSSNT) is applied to various two‐dimensional weakly singular integrals. A study of the different methods reveals complex relationships between transformation orders, position of the singular point, integration kernel and basis function. It is concluded that the GSSNT method gives the best overall results for the two‐dimensional weakly singular integrals studied. Copyright © 2002 John Wiley & Sons, Ltd.     

地统计克立格插值法在工程土方计算中的应用

土方计算是工程中经常碰到的问题。尝试利用地统计学的克立格插值法来计算土方，将其应用于余姚市泗门镇土地整理工程中进行实测试验。介绍了其基本的原理和公式，并与利用数字高程模型计算得到的土方工程量进行了比较，发现地统计插值法可较精确地确定设计标高和土方量，证明该方法的可行性和优越性。