挖掘机工作装置实验样本长度确定方法及程序系统

本文通过对某液压挖掘机工作装置实验样本长度的研究,详细讨论了样本长度的确定方法,重点分析了趋势曲线拟合法,提出了样本长度精度区间分析的方法,并在处理大量实验数据的基础上,从载荷分布及寿命估算的角度做了实际的验证.编制了应用程序,使样本长度确定至寿命估算整个过程程序化.     

Construction of transmission lines above valuable standing timber

Problems with the construction of transmission lines above a forest are examined. Construction of lines above standing timber makes it possible to shorten the length of the route, eliminate the clearing of a continuous swath along the line, and reduce the volume of in-service work. To implement this solution, it is necessary to introduce changes and supplements to existing regulatory technical documents. __________ Translated from élektricheskie Stantsii, No. 10, October 2007, pp. 48–51.     

光纤光栅的长度对其峰值反射率的影响

利用耦合模理论,数值分析了当光纤光栅(FBG)折射率变化为均匀分布、直流切趾高斯分布时,光纤光栅长度对其峰值反射率的影响。研究结果对光纤光栅外腔半导体激光器的设计和性能优化具有重要的意义。     

Alternating,all-trans polyenynes: Model compounds for poly(diacetylene)s with defined conjugation length

The syntheses of polyenynes as model compounds for poly(diacetylene)s (PDAs) are described. Variation of properties (UV–VIS, Raman, NMR and bond geometries) as a function of the chain length was investigated. After extrapolation to infinite chain length these data were compared to those for PDAs. From UV–VIS spectra a value of λ = 551 nm (2.25 eV) was calculated corresponding to the electronic transition of a single polyenyne chain. This energy is located at the low energy end of a yellow PDA solution spectrum. From Raman scattering v_(C?C) = 2108–2128 cm^?1 and v_(C?C) = 1505–1532 cm^?1 were calculated after extrapolation. Similarly sp-C¹³C NMR data yielded a shift of δ = 100 ppm. These data are almost identical to data known for yellow PDA solutions. Bond geometries are almost identical to those of poly(diacetylene)s and theoretical data.     

定向爆破拆除高危烟囱的实践

通过对已产生纵向裂缝、倾斜和基部风化剥蚀严重的高危烟囱的定向（向倾斜相反方向）倒塌爆破实践表明：设计中选用爆破参数及施工措施是有效的。     

Machining with tool–chip contact on the tool secondary rake face—Part II: analysis and discussion

The forces, chip thickness, and natural tool–chip contact length in machining with a double-rake-angled tool are predicted in Part II of the present study. It is revealed that in comparison with a single-rake-angled tool, a double-rake-angled tool increases the forces, especially the thrust force. However, the increase in chip thickness and tool–chip contact length is not significant under the input conditions specified in the present study. The effect of seven input variables of the proposed model is quantitatively investigated. The predicted variations of forces, chip thickness, and natural tool–chip contact length are in good agreement with theoretical and experimental results obtained by other researchers. The interrelationships among the resultant force, the chip thickness, and the natural tool–chip contact length are established, which provides a new and promising method to estimate the tool–chip contact length by employing the resultant force. It is demonstrated that the model can also be extended to study the problem of machining with a groove-type chip breaker tool.     

ADSS光缆的力学计算

介绍了ADSS光缆的力学计算，给出了光缆弧垂、张力、应变和悬长等计算公式，并对普遍采用的“悬链线”和“抛物线”两种计算方法加以比较。     

绕扰流片分离流动的壁面压力测量

在风洞中用电子扫描阀进行测压实验，研究了底部间隙和锯齿高度对扰流片引起的壁面压力分布的影响。结果表明底部间隙在g／h≥1．0时对扰流片上游壁面压力分布曲线有较大影响，而对下游回流区压力分布曲线的影响主要在0≤g／h≤2．0的区域内；并且在g／^=0．2、1．0时，流动结构发生改变。另外，锯齿扰流片的当量面积与平板扰流片相等时，锯齿高度对下游底板压力分布特性的影响亦主要限于0≤x／h≤2．0的区域。     

Short fibre elastomer composites: effect of fibre length,orientation, loading and bonding agent

A series of short fibre reinforced styrene butadiene rubber (SBR) composites were prepared by incorporating sisal fibres of different lengths and different concentrations. The vulcanization behaviour and the properties of the vulcanizates were measured by the relevant ASTM procedures. The processing characteristics such as green strength and mill shrinkage were improved by the addition of fibres. The properties like tensile strength, tear strength, moduli at 10% and 20% elongations were found to be maximum for composites containing longitudinally oriented fibres of length 6 mm. Mixes containing 35 phr loading of fibres and bonding agent showed better mechanical performance than others. The failure behaviour of tensile and tear specimens have been analysed by scanning electron microscopy techniques. Paper presented at the poster session of MRSI AGM VI, Kharagpur, 1995