少片渐变刚度钢板弹簧的优化设计与计算

讨论了渐变刚度钢板弹簧的载荷、变形量、刚度和应力的计算，建立了少片渐变刚度钢板弹簧的优化数学模型，利用MATLAB优化工具箱进行优化，并给出了计算实例。     

Calculation of cooling rate of amorphous aluminum alloy melt-spun ribbons

Based on the heat transfer theory and liquid solidification theory, the heat transfer during the rapid solidification process of amorphous ribbons prepared by melt spinning was approximately modeled by one-dimensional heat conduction equation. Besides, integration with the temperature gradient, the relationship between the ribbon thickness and solidification time was derived according to the boundary conditions of ribbon-copper wheel. A simply theoretical model was obtained to calculate the cooling rates of aluminum amorphous ribbons. According to the above theoretical model, the critical cooling rate of aluminum amorphous ribbons by melt spinning is above 10^6 K/s, which proves that the aluminum based alloys belong to the marginal glass forming ability of alloys. The calculated results are in good agreement with other estimated values reported previously.     

石油钻采阀门内壁热丝TIG堆焊

石油钻采专用阀门的使用有耐强腐蚀性要求，制造时需在内壁表层堆焊耐腐蚀材料。此类阀门具有质量大、形状特殊、焊接可达性差，焊接质量要求严格等特点；重点介绍了Fronius热丝TIG焊工艺和ETR全自动堆焊设备在阀门堆焊制造上的应用。     

Effect of temperature on mechanical behavior of AZ31 magnesium alloy

Strain rate sensitivity and tension/compression asymmetry of AZ31 magnesium alloy at different temperatures and strainrates were investigated.Both of mechanical behaviors are temperature dependent.Strain rate sensitivity increases with increasingtemperature.Thermally activated slip is the source of strain rate sensitivity.At the temperature below or near 373 K,strain ratesensitivity is very little.Tension/compression asymmetry in yielding decreases with increasing temperature.Twinning is the reasonof tension/compression asymmetry.At the temperature above or near 573 K,the material shows little tension/compressionasymmetry of the flow stress.     

凝固速率对定向凝固合金DZ22枝晶臂间距和枝晶偏析的影响

采用新研制的超高梯度定向凝固装置，研究了不同凝固速率下定向凝固高温合金ＤＺ２２枝晶臂间距和枝晶偏析。结果表明，冷运速率增大，枝晶臂间距显著细化，枝晶偏析被强烈抑制。当冷运速率为５２．４Ｋ．ｓ＾－１时，一次、二次枝晶臂间距λ１和λ２分别为２８．８和８．４μｍ，Ｎｂ，Ｔｉ，Ａｌ，Ｃｒ，Ｃｏ，Ｗ等元素的偏析比均趋近于１。     

水基淬火液用于汽车轴管零件的淬火冷却

在分析几种淬火液的基础上 ,选用冷却速度与快速淬火油相近的FEROQUENCH 2 0 0 0淬火液用于轴管淬火冷却 ,淬火后的轴管彻底消除了淬火裂纹 ,而且改善该零件热处理后的力学性能。     

ZG3Cr18Ni25Si2耐热钢熔炼工艺的改进

介绍改进后的ZG3Cr18Ni25Si2耐热钢熔炼工艺及其特点.具有较高的合金元素收得率,铸件使用寿命比改进前延长35%～45%.     

碳化硅晶须双重加热合成的研究

双重加热法是低成本、大批量合成碳化硅晶须的新技术，合成温度低、合成时间短、生成率高。对以炭黑和二氧化硅微粉为原料、用双重加热法合成碳化硅晶须的工艺过程进行了研究。观察了不同合成时间、合成温度和催化剂条件下的碳化硅晶须，揭示出不同工艺参数对合成的碳化硅晶须的产出率，微观形貌、直径和长度范围的影响。结果表明，催化剂的使用可以加快反应速度，提高碳化硅晶须的生成率，合成过程为VLS。实验中初步得到的最佳经济工艺参数为：Fe2O3的用量为2％，合成时间为1．5h，合成温度为1250℃。此时的该工艺条件下碳化硅晶须的生成率可达80％，晶须平均直径为0．6μm，平均长度为30μm。     

几种添加剂对模型石膏性能的影响

研究了N型减水剂、硅溶胶等添加剂对模型石膏凝结时间、强度、吸水率、溶蚀率等性能的影响,并确定了有关性能与添加量之间的关系,得出了最佳添加量。     

超声波处理微污染水体技术研究

考察了用超声波降解水中低浓度三氯乙腈、氯代苦味碱、溴苯的动力学，并从工程角度分析了多种污染物共存、自然水体等复杂状态下的可行性。探讨了采用空气鼓泡、不控水温的操作方式。结果表明超声波可以较快地去除复杂水体中的多种有机污染物，氧化可在批式反应器与连续流反应器中进行，高流速可以提高反应器的空间与能量利用效率。