集中载荷作用下的套管抗挤能力分析

根据油田套管损坏情况,建立了集中载荷作用下的套管抗挤能力计算模型,利用能量法和曲杆理论,分析研究了承受180°对称分布集中载荷、90°均匀分布集中载荷和120°均匀分布集中载荷下中厚壁套管抗挤能力,得出了理想圆管抗挤强度和套管屈曲临界挤毁压力的计算公式,通过分析比较理论解与有限元解,其最大相对误差不超过1%,得出了套管抵抗局部载荷的能力低于抵抗均布载荷的结论。     

精对苯二甲酸反应器桨叶断裂分析与修复

为了保证进口精对苯二甲酸装置氧化反应器中钛制搅拌器的正常工作，对钛制搅拌器桨叶在运行中断裂脱落的原因进行了分析，并叙述了桨叶修理的方法和要求。经修理后的桨叶投入生产使用，达到了预期的目标。     

Morphological aspects of rubber fracture and wear

Morphology of carbon black (CB)‐filled rubber was studied with AFM and SEM and the classification of filler agglomerates, based on their internal structure and filler–matrix interactions, has been proposed. It varies according to the activity of CB and the kind of rubber. It has been shown that fracture of rubber starts either inside filler agglomerates (de‐cohesion) or in a filler–matrix interphase (de‐adhesion) initiating wear of the material. Microscopic observations correlate well with TGA and EPR data of wear debris collected during friction of rubber. The increase of thermal stability of CB and the appearance of additional spin signals, respectively, for elongated samples or debris, are proposed to be associated with de‐cohesion or de‐adhesion of the agglomerates. New approach to the fracture of rubber called “fatal agglomerate concept” is presented. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

小生境遗传算法AVOA反演

采用具有水平对称轴的横向各向同性(HTI)模型研究裂缝性油气藏,P波振幅随炮检距和方位角变化(AVOA),表现出较强的方位各向异性特征。本文基于Ruger提出的HTI介质模型的P波反射系数公式,利用由基准测线和另外两条与之呈45°、90°测线的P波反射系数的相对差异估算裂缝方位;同时引入小生境遗传算法,对基准测线和与之呈90°测线的P波反射系数差进行反演,得到了较高精度的纵、横波波速比和Thomsen各向异性参数。     

就地补偿在动力厂水泵电机上的应用实例

本文就我公司动力厂给水车间155kW水泵电机，进行无功就地补偿的可行性分析及经济效益研究，对工厂用电如何节能降耗有一定参考价值观。     

Crack redirection with thermal secondary loading

In the current paper crack redirection due to a strategic placing of a heat source in the vicinity of a crack tip is studied. Analysis suggests that for PMMA and considered temperature range the only factor responsible for the deviation of crack trajectory is thermal stress. The simulation of crack growth in PMMA under external tension and secondary heat loading shows that a moving heat source in the vicinity of a crack tip can serve as a pointer for the crack trajectory. In highly conductive materials, redirection can be possibly effected with low-power thermal dipoles.     

Bruchanalyse an Hohlgläsern

Failure analysis of hollow glasses The failure analysis is very important to clarify damages of hollow glasses. Damages of glass bottle through over pressure are very often linked with damages to persons. This is the reason why the causal research is from particular importance. Different surface characteristics of glass fragments as well as the fracture pattern give hints to the direction of the crack, the stress just before breakage and the reason of stress. A reconstruction of the bottle is a further helpful instrument for cause studies. The difference of the various characteristics of the surface will be explained. Further on there will be discussed different reasons and mechanism of fracture.     

Probabilistic cell modelling of cleavage fracture

Various aspects on probabilistic modelling of cleavage fracture are discussed. The investigation involves consideration of a unit cell with an explicitly modelled void. The results from this model are compared with results for the case when the void content is accounted for in the sense of a Gurson-Tvergaard law. It is found that explicit modelling of the void can give substantially different results for the fracture probability. The effect depends on the exponent in the assumed Weibull distribution, the threshold stress, the constraint conditions and the hardening of the material. This revised version was published online in August 2006 with corrections to the Cover Date.     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

二滩电厂双缸液压启闭机原理及故障分析

二滩电厂表孔采用弧形门,启闭形式为双缸液压启闭机.自投入运行以来,运行状况良好.汛期启闭方式已由原来的现地手动操作过渡到远方控制自动启闭.在闸门起落的过程中,由于工况的不同,两缸会出现不同步现象,因此设计中考虑了纠偏回路.本文简单介绍了二滩电厂表孔液压启闭机的原理和故障情况.