利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

离心式高炉鼓风机扩压叶片断裂事故分析及处理

通过高炉鼓风机扩压叶片断裂事故，从化学分析、物理检验，结合使用情况对扩压叶片断裂原因进行了详细分析，并提出了改进措施。     

Microscale and mesoscale discrete models for dynamic fracture of structures built of brittle material

In this work we present the discrete models for dynamic fracture of structures built of brittle materials. The models construction is based on Voronoi cell representation of the heterogeneous structure, with the beam lattice network used to model the cohesive and compressive forces between the neighboring cells. Each lattice component is a geometrically exact shear deformable beam which can describe large rigid body motion and the most salient fracture mechanisms. The latter can be represented through the corresponding form of the beam constitutive equations, which are derived either at microscale with random distribution of material properties or at a mesoscale with average deterministic values. The proposed models are also placed within the framework of dynamics, where special attention is paid to constructing the lattice network mass matrix as well as the corresponding time-stepping schemes. Numerical simulations of compression and bending tests is given to illustrate the models performance.     

Tensile fracture and failure behavior of technical flax fibers

The apparent tensile strength of technical flax fibers was determined in single‐fiber tests at various clamping lengths (20, 40, and 80 mm) and the outcome was compared with literature data. It was demonstrated that the strength of flax at each clamping length obeyed the two‐parameter Weibull model. The failure mode and sequence were studied in situ (i.e., during loading) by SEM and acoustic emission (AE). The failure sequence (axial splitting of the technical fiber along its elementary constituents, radial cracking of the elementary fibers, multiple fracture of the elementary fibers) concluded reflected the hierarchical build‐up of the flax bast fibers. To the above failure events AE amplitude ranges were assigned. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3638–3645, 2003     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

一种可切削玻璃陶瓷的压痕断裂特性

将断裂韧性测试的压痕方法与压痕弯曲方法相结合，独立地分离出了压痕残余应力因子ｘ，使其成为可测参量，并建立了压痕一压痕弯曲的断裂韧性测试方法．将这种方法应用于一种可切削玻璃陶瓷的测试，获得的Ｋ１ｃ值为Ｋ１ｃ＝２．０３ＭＰａ·ｍ１／２，与单边切口法（ＳＥＮＢ）获得的Ｋ１ｃ值有较好的一致性．测得的残余应力因子Ｘ＝０．０９３，符合Ａｎｓｔｉｓ经验公式的预测．     

VCM压缩机曲轴断裂失效分析

介绍了锦化化工(集团)有限责任公司出现的VCM压缩机曲轴断裂事故，并从断口的部位、形貌特征，断轴的几何状态、受力状态及树料性能等方面分析了曲轴断裂的根本原因。     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.