拉盖尔-高斯光束通过有硬边光阑光学系统的传输

采用将硬边光阑展为有限个复高斯函数之和的方法,得到了拉盖尔-高斯光束通过有硬边光阑近轴ABCD光学系统中传输的近似解析公式,作了数值计算以说明传输公式的应用,并对使用该式的误差作了讨论。     

镍代钴矿用硬质合金的新进展

概述了镍代钴矿用硬质合金的国内外进展情况．     

铵离子交换处理负硬水供锅炉应用技术

本文论述了负硬水只用氯化铵再生时离子交换器的运行过程及离子交换软化除碱的方法,并阐述了控制出水中残留碱的简便方法。经研究证明,此方法可达到除碱度、除硬度、除盐、延长锅炉使用寿命、减少腐蚀、减少排污量、节约燃煤等效果。经济效益十分显著。     

添加VC的TiB2基硬质材料研究

对添加VC的TiB2基硬质材料进行了研究。通过实验测定了硬度、横向断裂强度、高温强度以及耐磨性等性能，通过观察SEM照片研究了VC对TiB2基硬质材料组织结构的影响。综合各种指标，我们确定在TiB2-Fe—Mo硬质材料中VC的最佳添加量为0．5％。     

Adhesion studies of diamond-like carbon films deposited on Ti6Al4V substrate with a silicon interlayer

Diamond-like carbon (DLC) films have proven quite advantageous in many tribological applications due to their low friction coefficient, their extreme hardness, and more recently their high adherence on different substrate materials. However, for many applications, DLC films as thick as 2 μm are required, which cause high residual stress. In order to overcome this problem, this study observed the behavior of different thicknesses of silicon interlayer between DLC films and Ti6Al4V substrates. The study also analyzed the relation of growth parameters to the mechanical properties of DLC films. Silicon and DLC films were grown by using a rf-PECVD at 13.56 MHz with silane and methane atmospheres, respectively. The contribution of an interlayer thickness to the adhesion between the DLC films and Ti6Al4V substrate was evaluated by using a micro-scratch technique. The hardness and friction coefficient were evaluated by using microindentation and lateral force microscopy (LFM), respectively. Raman scattering spectroscopy was used to characterize the film quality. A correlation was found between the intrinsic stress and adhesion of DLC film and the parameters of the silicon interlayer growth. The addition of a silicon interlayer successfully reduced intrinsic stress of the films, even as measured by using a perfilometry technique.     

提高硬质合金工具使用寿命的研究

通过改变硬质合金剩余应力类型和状态，改善了硬质合金的性能，提高了硬质合金工具的使用寿命。     

基于FPGA的数字下变频SDR-PHS系统的设计及实现

软件无线电SDR(Software Defined Radio)技术改变了传统的硬件无线电平台,是一种具有弹性的软件无线电平台,它支持不同的无线通信标准和系统的要求。而现场可编程门阵列FPGA(Field Programmable Gate Array)由于其可灵活编程的特点,其处理能力、逻辑资源规模的不断增强,在需要灵活配制的SDR设计中承担着越来越重要的角色。本文从软件无线电的设计思想出发,描述一种应用于个人手持式电话系统PHS(Personal Handyphone System)中基于FPGA的数字下变频SDR处理方案的设计分析及其实现过程,阐述基于硬限幅和RSSI幅度信息恢复的低成本SDR实现方法。仿真试验结果验证了该方法的有效性和可靠性。     

印尼某火电厂Ａ２—Ａ４区人工边坡失稳机制研究

以印尼某火电厂涉外项目Ａ２—Ａ４区的问题人工边坡为研究对象,通过现场地勘、实际变形失稳过程、数值模拟等方法综合研究了该地人工边坡失稳机制。在此基础上,探讨了边滑坡加固措施的作用效果及合理性。所得主要结论:Ａ２—Ａ４区人工边坡变形失稳机制主要为软弱地层（煤层）切穿暴露所造成的组合滑移以及坡体沿土岩分界面所造成局部变形,变形破坏模式接近圆弧滑动,人工边坡中的软弱夹层是导致边坡失稳的主控因素;Ａ２、Ａ４区综合考虑桩锚＋坡面锚杆的方式进行加固,煤层和全风化泥岩及上部土层内的组合变形没有发展贯通趋势,边坡整体安全。Ａ３区在加固作用下存在沿二级坡脚＋煤层＋全风化泥岩＋上部土层内越顶组合滑移风险以及基坑开挖造成基坑侧壁坍滑风险,需要引起重视并加强监测。