New liquid membrane technology for simultaneous extraction and stripping of copper(II) from wastewater

In this paper, a new liquid membrane technique, hollow fiber renewal liquid membrane (HFRLM), is presented, which is based on the surface renewal theory, and integrates the advantages of fiber membrane extraction, liquid film permeation and other liquid membrane processes. The results from the system of CuSO₄+D2EHPA in kerosene+HCl show that the HFRLM process is very stable. The liquid membrane is renewed constantly during the process, the direct contact of organic droplets and aqueous phase provides large mass transfer area. These effects can significantly reduce the mass transfer resistance in the lumen side. Then the mixture of feed phase and organic phase flowing through the lumen side gives a higher mass transfer rate than that of stripping phase and organic phase, because the aqueous layer diffusion of feed phase is the rate-controlling step. The overall mass transfer coefficient increases with increasing flow rates and D2EHPA concentration in the organic phase, and with decreasing initial copper concentration in the feed phase. The overall mass transfer coefficient also increases with increasing pH in the feed phase, and reaches a maximum value at pH of 4.44, then decreases. Also, there is a favorable w/o volume ratio of 20:1 to 30:1 for this process. Compared with hollow fiber supported liquid membrane and hollow fiber membrane extraction processes, HFRLM process has a high mass transfer rate. Mathematical model for the HFRLM process based on the surface renewal theory is developed. The calculated results are in good agreement with experimental results under the conditions studied.     

三(苄基硫醇)锑的合成及其应用性能

以苄基硫醇、三氧化二锑 (或三氯化锑 )等为原料 ,研究了三 (苄基硫醇 )锑的最佳合成工艺条件 ,产率分别达到 90 %和 95 %。用元素分析法及红外光谱技术对产品进行了表征 ,热分析技术 (TG和DSC)研究表明 ,含合成产物的聚氯乙烯 (PVC)制品的初始分解温度在 2 2 0℃以上 ,其热分解效应为 1 1 5 5J/g。热老化研究表明 ,当合成产物添加量达 1 5份 (PVC质量为 1 0 0份 )时 ,PVC树脂的热稳定时间为 1 8min(2 0 0℃ ) ,当其与硫醇钡以质量比 3∶1复配时 ,可显著提高PVC制品的长期热稳定性     

Acetyl‐capped paraformaldehyde as crosslinking agent for BMI‐modified novolac resin for resin transfer molding

Paraformaldehyde was end‐capped with acetyl groups and was applied as a crosslinking agent for a bismaleimide (BMI)‐modified novolac resin system. The processibility of the resin system containing 5 wt % crosslinking agent still met the need for resin transfer molding (RTM), whereas the thermomechanical properties of crosslinked resin improved significantly. The composites based on the resin system and woven glass fabric showed better flexural strength, modulus, and higher retention rates at 200 and 300°C than that based on a resin system without acetyl‐capped paraformaldehyde. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1265–1271, 2002     

通气式搅拌槽的传热特性

研究了通式搅拌槽槽壁给热系数（ｈｗ）随通气速率和搅拌转速变化的规律和机理，在搅拌过程中存在一个临界转速，它决定了通气是增大还是减小ｈｗ。通过引入综合反映操作条件对ｈｗ影响的无因次数Ｈｚ，获得了一个偏差较小并且简单实用的ｈｗ半经验关联式。     

高压蒸汽管道保温研究

计算了不同管径和保温厚度下蒸汽管道输送高压蒸汽的热损失和温度降。结果表明:保温厚度越大,蒸汽的热损失越小、温度降越小;保温材料导热系数与蒸汽的热损失呈正比;环境温度越高,蒸汽的热损失越小;环境风速对热损失的影响不大。同时研究了保温材料选择和保温结构对节能的影响。     

硝酸废热锅炉的腐蚀与防腐

结合本厂硝酸装置的实际，分析废热锅炉的腐蚀机理，介绍硝酸废热锅炉的防腐措施。     

流态化炉活性炭生产中的余热利用

用流态化炉生产颗粒活性炭时，在尾气通道上设计了一套余热回收装置，并用余热加热流态化反应所需的空气及水蒸气，该装置也能自产蒸汽，最大蒸汽发生量为70kg／h，余热换热器热利用率为42．7％。     

The kinetics of hydrogen transport through amorphous Pd82−yNiySi18 alloys (y=0-32) by analysis of anodic current transient

Hydrogen transport through amorphous Pd_82−yNi_ySi₁₈ alloys (y=0-32) was investigated in 0.1 M NaOH solution by analysis of the anodic current transient. It was found that the anodic current transient shows the non-Cottrell behaviour, but its shape and value remain nearly constant regardless of the hydrogen discharging potential. From the coincidence of the anodic current transient theoretically calculated with that experimentally measured, it is suggested that the change in surface concentration of hydrogen with time is uniquely given by the rate of hydrogen transfer from absorbed state at the electrode sub-surface to adsorbed state on the electrode surface. This means that neither the ‘constraint of constant concentration’ nor the ‘constraint by Butler-Volmer behaviour’ is effective at the electrode surface during hydrogen extraction. On the basis of the theoretical current-time relation under the ‘constraint by hydrogen transfer of absorbed state to adsorbed state’, the hydrogen diffusivity was determined to have an almost constant value of (1.3±0.4)×10⁻⁸ cm² s⁻¹, irrespective of the Ni content and in the absence of Ni. On the other hand, it is inferred that the rate constant of hydrogen transfer decreases markedly with increasing Ni content due to the Ni(OH)₂ layer formed on the electrode surface.     

The Effects of Power Law Fluid Rheology on Coil Heat Transfer for Agitated Vessel in the Transitional Flow Regime

A CFD model of heat transfer from power‐law fluids to helical cooling coils in the transitional flow regime of a baffled tank mixed with a pitched blade turbine was developed with Fluent^TM. The model captured local temperature and velocity gradients. Simulations were run, varying Re, Pr, K and n. The results indicate that a Sieder‐Tate type correlation, with the exponent on and the coefficient in front of the Reynolds number being a function of n, is recommended for estimating ho. Also, a new two coil bank design was found to be more efficient when 450 < Re < 650.