壳聚糖和粉煤灰对间甲酚的吸附处理

用壳聚糖和粉煤灰对含间甲酚的废水进行吸附处理,考察了壳聚糖的用量、振荡时间、振荡速度以及粉煤灰与壳聚糖的混合比对处理效果的影响.结果表明:在常温下,对于初始质量浓度为56 mg/L的间甲酚,当壳聚糖用量为3 g/L,以170 r/min的转速吸附振荡0.5 h,去除率可达到88%以上;在上述条件下,加入质量比4:1的粉煤灰与壳聚糖混合物5g/L时,间甲酚的去除率可达到91%.     

Temperature effects on the mass flow rate in the SBI and similar heat‐release rate test equipment

In various medium‐to‐large‐scale fire test equipments like the ISO room corner test (RC), and more recently, the single burning item test (SBI) the mass flow rate measurement of the combustion gases plays a key role in the determination of the heat‐release rate and smoke‐production rate. With the knowledge of the velocity profile and the temperature of the flow, the mass flow rate is obtained by measuring the velocity on the axis of the duct. This is done by means of a bi‐directional probe based on the pitot principle. However, due to the variation of the mean temperature and the temperature gradient in any cross section of the duct, introduced by ever changing combustion gas temperatures, the velocity nor the density profile are constant in time. This paper examines the resulting uncertainty on the mass flow rate. Copyright © 2006 John Wiley & Sons, Ltd.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

胜科1井钻井事故的预防与处理

胜科1井设计井深7 000 m,完钻井深7 026 m。在该井钻井过程中,针对上部大尺寸钻头破岩效率低、大井眼井壁稳定性差、大段盐膏层、膏岩层的塑性蠕变和塑性流动造成井眼复杂、超深井高温高压给钻井液性能的控制和水泥浆调控等带来的一系列技术难题,制定了一整套预防井下事故和复杂情况的技术措施,从而确保了该井的钻探成功。该井在钻井过程发生了2次断钻具事故和1次卡钻事故,根据超深井的特点,采取了较为稳妥的处理措施,同时,有针对性地研制了高效铣环和PDC钻头专用打捞器,3次事故处理均获得了成功,共耗时38.5 d。详细介绍了该井所采取的预防和处理钻井事故的技术措施,可为其他超深井的钻井施工提供一定的借鉴。     

滚动转子式压缩机传热模拟

就滚动转子式压缩机的传热特性进行了分析。把压缩机分为15块，视摩擦损失和电机发热为内热源，考虑润滑油流动在传热过程中的影响，应用集中参数法对每块进行了能量分析，建立了传热数学模型并进行了计算。     

Influence of the Preheat Treatment on the Microstructure and Properties of X37CrMoV5-1 Steel

The technological properties of the hot-work tool steels depend on their microstructural quality induced by the production process and the heat treatment. One of the frequently applied methods to improve microstructure is preheat treatment. The treatment of carbonitriding X37CrMoV5-1 steel has been investigated in fluidized bed furnaces. Thickness and phase composition have been conducted using optical microscopy Neophot 32 and scanning microscopy, JEOL 5400, after etching in nital.     

浅埋地下建筑风冷热泵空调系统传热模型与试验研究

本文在浅埋地下建筑风冷热泵空调系统围护结构传热动态模拟的基础上，通过对南京市太园地下旅社围护结构传热的实时测试，验证动态传热模型及计算机模拟方法的可行性和正确性，为浅埋地下建筑风冷热泵空调系统的装机容量、节能指标和设计计算提供一定的理论依据。     

节能降耗提高矿山效益

节能降耗是每一个矿山提高经济效益的有效途径。我们采取提高球磨机处理能力，降低单耗；利用“分时计价”政策，采用“避峰作业”；使用新设备等措施节能降耗，提高矿山经济效益。     

论普通型胶辊表面不处理的合理工艺参数

论述了普通胶辊表面不处理的性能特点和存在问题，技术措施和合理工艺参数，提高了成纱条干水平，减少缠绕和磨损。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.