不同分散剂对细粒高硫煤及煤系黄铁矿的选择性分散

主要研究六偏磷酸钠和腐植酸纳２种分散剂分别对细粒高硫煤、煤系黄铁矿悬浮液的分散作用，考察了分散剂用量、介质ｐＨ值对细粒煤与煤系黄铁矿选择性分散的影响。     

采用高速剪切反应器生产超细氧化铋工艺探讨

利用硝酸铋溶液和碳酸铵溶液为原料，采用高速剪切反应器，500℃煅烧后可以生产出高纯、超细的氧化铋粉末。该方法制备出的氧化铋平均粒度0．71μm且粒度范围分布窄，颗粒形貌为类球形，晶相为纯α相，指标达到电子压敏陶瓷要求。由于粒度细小，可以在电子压敏陶瓷球磨工艺减少球磨工艺，并具有更好的分散效果。本文对超细的氧化铋粉末形成机理也进行了探讨。     

涵闸工程施工期混凝土温度监测系统与水化热参数反演

针对涵闸工程混凝土温控防裂需要,研制了全自动化数字测温系统。该系统的硬件部分由数字式温度传感器、采集单元、GPRS DTU组成,软件部分包括中心服务器软件和客户端软件。系统实现了GPRS公用无线网络覆盖范围内无人值守、多测点远程测量和数据实时共享,具有体积小、无需布线、运行稳定、精度高等特点。经过实际工程多次应用,系统运行稳定可靠,达到预期性能。基于以上系统的测量数据,结合三维非稳定温度场数值计算,对特定工程的水化热参数进行了反演。规范给出普硅42.5水泥水化热参数为m=0.69,n=0.56;而根据实测数据反演的结果为m=1.85,n=0.79。根据两组参数分别进行了三维温度应力计算,得到完全不同的计算结果,前者温度应力未超标,后者多处超标需要采用温控防裂措施才能保证结构防裂安全。因此对实际工程进行温度监测和水化热参数反演是非常必要的。     

含碘高氯乳剂的制备和性能研究

碘离子掺入到高氯乳剂可以显著提高其感光性能。碘离子掺入到亚表层可增加乳剂的光吸收,提高感光度,增加反差。最佳掺入量为0.6％mol/mol Ag,掺入位置在65％Ag处,KI加入速度约8s。在一定范围内(小于1.5％mol/mol Ag)碘离子掺入亚表层对清晰度没有明显影响。如果铱掺杂的掺杂位置为亚表层,掺杂量为10~(-7)mol/mol Ag,铱络合物可有效地改善含碘高氯乳剂的高照度互易律失效。     

Binder effect on cycling performance of silicon/carbon composite anodes for lithium ion batteries

The cycling performance of a silicon/carbon composite anode has been significantly enhanced by using acrylic adhesive and modified acrylic adhesive as binder to fabricate the electrodes for lithium ion batteries. The capacity retentions of Si/C composite electrodes bound by acrylic adhesive and modified acrylic adhesive are 79% and 90% after 50 cycles, respectively. These two binders are electrochemically stable in the organic electrolyte in the working window. They also show larger adhesion strength between the coating and the Cu current collector as well as smaller solvent absorption in the electrolyte solvent than polyvinylidene fluoride (PVDF). Furthermore, sodium carboxyl methyl cellulose (CMC) plays an important role on improving the properties of acrylic adhesive, which increases the adhesive strength of acrylic adhesive and improves the activation of the electrodes.     

羧基化高纯单壁碳纳米管修饰电极对乙酰甲喹的高灵敏检测

采用羧基化高纯单壁碳纳米管(c SWCNTs)固载于金电极表面来构筑乙酰甲喹电化学传感器。运用循环伏安法(CV)、差分脉冲伏安法(DPV)和电化学交流阻抗法(EIS)测定传感器的性能。结果显示,该传感器对乙酰甲喹的电化学还原具有显著的催化性能,修饰电极的峰电流达到-128.40μA,是裸电极峰电流的1167倍。通过对传感器性能影响因素的考察,得到最优制备条件为cSWCNTs涂覆量为4μL(质量分数0.10%分散液),搅拌速度1000 r/min,pH=7.0的PBS浓度为0.2 mol/L,-0.5V电压下富集30 min。在该条件下制备的传感器峰电流与乙酰甲喹在1～500nmol/L范围内呈良好的线性关系,相关系数为0.998,方法的检出限为0.76nmol/L。该传感器被成功地应用于实际样品检测,加标回收率在81.7%～124.0%。     

α-Fe2O3/煤矸石复合光催化剂的制备及其降解五氯酚性能的研究

以Fe（NO₃）₃、煤矸石和NaOH为原料,采用沸腾回流法制得了一系列不同质量比的α-Fe₂O₃/煤矸石复合光催化剂。采用场发射扫描电子显微镜（FESEM）、X射线衍射仪（XRD）及紫外-可见漫反射光谱（UV-Vis DRS）等多种手段对产物做了表征。以五氯酚为目标降解物,考察了模拟太阳光照下样品的光催化效果。结果表明,将球形α-Fe₂O₃负载于改性煤矸石表面可有效提高其光催化活性,且α-Fe₂O₃/煤矸石复合光催化剂的性能与α-Fe₂O₃的含量有关,当α-Fe₂O₃与煤矸石的质量比为30∶100时,样品的光催化效果最佳,180 min内即可将五氯酚降解完全。此外,α-Fe₂O₃/煤矸石复合光催化剂还具有可重复使用的特点。     

高铝质强化日用瓷釉料

通过调整软质熔剂和硬质熔剂的种类和数量 ,研制出了适合刚玉质强化瓷的釉面硬度 7373MPa、白度 75 .9%、光泽度 89.3%且高热稳定性的透明釉料     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

氮化硅反应烧结的研究进展

氮化硅作为高温功能陶瓷性能优越，但将其制备成陶瓷零件比较困难，目前一般用反应烧结法制备氮化硅陶瓷零件。此外，反应烧结制备氮化硅陶瓷还具有成本低、烧结温度低、产品成型好、陶瓷高温性能好等优点。综述了氮化硅陶瓷反应烧结工艺流程和工艺的优缺点，着重介绍了氮化硅反应烧结在成型工艺、烧结工艺、原材料影响、后处理和陶瓷增韧等方面所取得的进展。