Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

从7-ADCA生产过程中环境友好的回收苯乙酸

采用新工艺回收7-氨基-3-脱乙酰氧基头孢烷酸(7-ADCA)生产中产生的苯乙酸,并对苯乙酸回收过程中产生的废硫酸进行处理。采用硫酸(9 8%)洗涤二氯甲烷,硫酸与二氯甲烷适宜的体积比为1∶50,洗涤好的二氯甲烷中含苯乙酸4%。蒸馏出二氯甲烷,趁热向熔融苯乙酸中加入母液,降温析出苯乙酸。晾干的苯乙酸为白色鳞片状,含量大于99%,苯乙酸母液补充部分清水套用到下一批析出苯乙酸。废浓硫酸用芬顿试剂氧化,控制80℃氧化4h,双氧水和七水硫酸亚铁重量比为6∶1,废浓硫酸COD下降85%以上。氧化结束后向废硫酸中加入铁粉和双氧水,制得聚合硫酸铁。     

高精度多环片自动装配控制技术

为了实现对微小环片零件的自动化装配,搭建了自动装配系统.通过4根直线导向轴与4个直线轴承来提高系统的导向精度和刚度.采用直线导轨进行各装配作业模块之间的切换,保证了微小环片零件的自动装配与取出.在环片的装配方向上,螺旋升降机和光栅尺实现环片的位置精度控制.在Lab VIEW编程环境中,采用分层软件架构和模块化控制思想,避免了不必要的数据循环检测与丢失,能够达到环片组件的装配精度要求.控制系统分为系统初始化模块、参数设置模块、装配模块和取出模块,自动装配系统通过各个模块间的相互交流配合完成装配任务.采用本文中自动装配系统装配环片的实验结果表明,环片零件装配的最大位置误差为26μm,垂直度误差为17μm,平均装配时间为75 s/片,可满足环片组件所需的精度要求.     

一种军棋机器博弈的多棋子协同博弈方法

针对在军棋博弈不完全信息对弈中，面对棋子不同价值、不同位置、不同搭配所产生的不同棋力，传统的单子意图搜索算法，不能满足棋子之间的协同性与沟通性，同时也缺乏对敌方的引诱与欺骗等高级对抗能力。本文提出一种结合UCT搜索策略的高价值棋子博弈方法，实现高价值棋子协同博弈的策略。实战经验表明:高价值多棋子军棋协同博弈策略优于单棋子军棋博弈策略。     

High-Tg porous polyimide films with low dielectric constant derived from spiro-(adamantane-2,9′(2′,7′-diamino)-fluorene)

Porous polyimide (PI) films with low dielectric constants and excellent thermal properties have been a pressing demand for the next generation of high-performance, miniature, and ultrathin microelectronic devices. A series of novel porous PI films containing fluorenyl-adamantane groups were prepared successfully via thermolysis of poly(ethylene glycol) (PEG) added in the PI matrix. The cross-sectional morphologies of porous PI films showed closed pores with diameters ranging from 135 to 158 nm, which were uniform and regular in shape without interconnectivity. These porous PI films exhibited excellent thermal properties with a glass-transition temperature at 376 °C whereas the 5% weight loss temperature in air excess of 405 °C due to enhanced rigidity afforded by fluorenyl-adamantane groups. Accompanied by thermolysis content of PEG increasing from 0 to 20 wt %, the density of porous PI films decreased, and the corresponding porosity grew significantly from 0 to 11.48%. Depending on porosity, the dielectric constant and dielectric loss of porous PI films significantly declined from 2.89 to 2.37 and from 0.050 to 0.021, respectively. These excellent properties benefit the as-prepared porous PI films for application as interlayer dielectrics, integrated circuit chips, or multichip modules in microelectronic fields. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47313.     

高浓度聚合物驱提高采收率方法实验研究

为探索一种新的提高原油采收率的方法,在外形尺寸为4.5 cm×4.5 cm×30 cm、气测渗透率0.9~1.0μm2、变异系数为0.72的二维纵向非均质人造岩心上,模拟大庆油田油藏流体性质及温度条件,研究了高浓度聚合物(HPAM)驱注入时机、聚合物相对分子质量、聚合物段塞体积及段塞组合对驱油效果的影响。通过注入大分子量、高浓度聚合物,结合合理的注入方式,在化学剂成本与三元复合驱相当的情况下,采收率比水驱提高20个百分点以上,接近或超过三元复合驱的水平。实验表明,采用高浓度聚合物驱油是一种较好的提高原油采收率的方法。     

水泥浆失水制约下套管与井眼间隙的研究

通过对水泥浆失水规律的室内试验分析以厦对注水泥顶替过程中水泥浆失水桥堵套管与井眼间隙问题的研究，建立了顶替过程中滤失层不发生水泥浆失水而桥堵环形空间的临界失水量计算模型，提出了调配水泥浆失水性能和确定合理套管井眼间隙的具体方法，对注水泥现场施工和井身结构设计具有一定的指导意义。     

高温高盐高含水油藏提高水驱采收率配套技术

针对江汉油区高温高盐高含水油藏的储层条件,应用国内外油藏精细描述、油藏工程最新理论与技术,提出了高含水油田合理钻加密井、完善注采井网、水平井挖潜、不稳定注水及高温高盐油藏采油工艺配套技术措施,形成了一套适应高温高盐高含水油藏提高水驱采收率的配套技术。     

一种可替代漂珠的低密度材料

漂珠低密度水泥浆由于密度低、强度高、体系稳定而在油田低压易漏层及低压油气层长封固段固井作业中获得了广泛的应用。但近年来,由于漂珠的产量越来越少,油田低成本要求急需开发代替漂珠的新型减轻材料,以满足配制低密度水泥浆的需求。开发了BCL-10S低密度混合减轻材料,其物化性能与漂珠相当,用它作减轻剂配制的低密度水泥浆性能与用漂珠作减轻剂配制的低密度水泥浆性能相媲美,并已经在长庆油田获得了应用。     

Efficient Low Dissipative High Order Schemes for Multiscale MHD Flows, II: Minimization of ∇·B Numerical Error

An adaptive numerical dissipation control in a class of high order filter methods for compressible MHD equations is systematically discussed. The filter schemes consist of a divergence-free preserving high order spatial base scheme with a filter approach which can be divergence-free preserving depending on the type of filter operator being used, the method of applying the filter step, and the type of flow problem to be considered. Some of these filter variants provide a natural and efficient way for the minimization of the divergence of the magnetic field (∇·B) numerical error in the sense that commonly used divergence cleaning is not required. Numerical experiments presented emphasize the performance of the ∇·B numerical error. Many levels of grid refinement and detailed comparison of the filter methods with several commonly used compressible MHD shock-capturing schemes will be illustratedA condensed version appears in the Proceedings of the International Conference on High Performance Scientific Computing, March 10-14, 2003, Hanoi, Vietnam. This is a revised version of a longer internal report, Feb. 19, 2004. The longer internal report was published as a RIACS Technical Report TR03.10, July 2003, NASA Ames Research Center