Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

玻璃钢包扎在煤气管道加强上的应用

介绍了玻璃钢包扎煤气管道的施工材料、施工流程及要点，指出了此方法应用在煤气管道加强上的优点。     

厚膜型无溶剂环氧重防腐涂料的研究

比较了不同环氧树脂、环氧固化剂、颜填料、助剂等的特性,制备了厚膜型无溶剂环氧涂料,并进行了各项性能的检测,结果表明,该涂料具有极低的VOC含量,符合环保要求,适用于要求长效防腐的钢构件。     

苯胺衍生物改性酚醛树脂的性能和结构表征

选用某种叔胺类化合物作苯酚和甲醛反应的催化剂,并加入少量苯胺衍生物,制备了一种分子量较高的改性酚醛树脂。根据IR、NMR和GPC的测试分析,对苯胺衍生物改性酚醛树脂的结构特征等进行了研究。它与环氧树脂合成压制的玻璃布层压板的浸水后绝缘电阻可达1011Ω以上,其它主要性能也达到了国外同类产品水平。     

常温冲孔性优良的CEM-1覆铜板的研制

本文介绍了一种CEM-1覆铜板的制作方法,采用这种方法制作的覆铜板具有优良的常温冲孔性和良好的性价 比。     

Adhesive Dispensing Process Analysis: Steady-State Dispensing of One-Component Adhesives

The process of dispensing one-component heat-cure adhesives was investigated in order to understand current application processes and to guide new process development. Typical one-component adhesives exhibit non-Newtonian rheological behavior, and hence Newtonian fluid mechanics does not adequately describe the dispensing process. In the present study, the adhesives were modeled as Bingham fluids possessing a yield stress and a steady state viscosity. The model of the dispensing apparatus includes four major flow sections connected in a serial configuration. The fluid mechanics equations derived for Bingham fluids in the individual flow sections were solved by numerical methods in order to understand the interrelationships between the material variables (e.g. yield stress, viscosity, temperature dependencies) and process variables (e.g. pressure, flow geometry, temperature, output). The concept of the model is generic and the details of the model can be modified for any forced-flow adhesive application process.

The adhesive flow properties significantly influence the process output. Dispensing temperature, among the process variables, has the strongest effect on process output. A ± 1.0·C perturbation in the dispensing temperature can cause as much as a 14% variation in the bead size for the range of adhesives studied. Differences in flow characteristics result in differences in processability and non-linear temperature/pressure sensitivity. The non-linear sensitivity can be eliminated by operating the dispensing process isothermally. Finally, the process limits for one-component adhesives, which are susceptible to chemical instability induced by viscous heating during processing, are defined and discussed in terms of a modified Brinkman number that takes into account viscous dissipation, heat conduction and convection, and chemical stability of the material during processing.     

环氧玻璃钢衬里在化工设备中的应用

本文叙述了非标准化工设备的环氧玻璃钢防腐衬里工艺、配方及使用考查结果．     

泥炭土地基钻孔漏浆的处理

以云南鸡石一级公路青鱼湾大桥为例，介绍了在软弱地层中施工桥梁钻孔灌注桩遇孔壁开裂漏浆时的处理方法，经试验证明，取得了较好的技术经济效果。     

WF40防腐蚀涂料在原料水罐上的应用

中国石化股份有限公司洛阳分公司炼油厂污水汽提装置的原料水罐(V303)由于接触的污水中含有H2S,NH3,CO2,CN-,酚等多种腐蚀介质因此经常发生腐蚀泄漏事故。经涂刷WF40玻璃鳞片防腐蚀涂料后,已平稳运行两年。2002年检修检查,涂层完好,仍在继续使用。WF40涂料为环氧型玻璃鳞片涂料,其热膨胀系数与钢质基体接近,因此具有耐热冲击性强等优点。待涂罐体经喷砂除锈到Sa2.5级后,涂底漆2道,中间涂层2道、面漆2道,使干膜厚度达到350μm,可有效防止腐蚀性介质的渗透。     

砌筑砂浆达不到设计要求的事故原因分析

从砂浆的配合比、和易性、原材料等对砌筑砂浆达不到设计要求的事故原因进行了分析。