Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

G104-5P42分支水平井钻井液工艺技术

G104-5P42井是在高尚堡G104-5区块构造较高部位部署的一口重点开发井，也是冀东油田第一口鱼骨型水平分支井，钻探目的是开发高浅北区Ng12油层，挖掘高浅北区井间剩余油潜力。该井主井眼斜深为2388m，水平位移为736．42m，水平段长243m，第一分支斜深为2342m，水平段长120．25m，水平位移为682．14m，第二分支斜深为2421m，水平段长117m，水平位移为761．73m。三开选用无固相甲酸盐聚合醇钻井液，在钻进油气层前加入GN-YBJ-I保护剂。应用结果表明，无固相甲酸盐聚合醇钻井液具有好的防塌能力和润滑减阻效果，性能稳定、黏度、切力较低，有利于减少环空压力损耗；在油气层段密度控制在1．08g／cm^3以内，为近年来同区块密度使用最低井，减小了有害固相及滤液对储层的伤害密度，经测试该井获高产油流；该井全井平均机械钻速为15．09m／h，钻井周期比原设计提前15d。该体系的配制及维护成本较高，适宜在目的层井段使用，但可回收再利用。     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

超高层建筑物下嵌岩桩荷载传递性状的长期观测

对美国费城自由广场一号塔楼下的Ｇ一１０号嵌岩桩（８．８ｍＸ２．６～３．０ｍ，设计荷载５３８４９ｋＮ）在成桩后数月及上部结构施工期间和竣工后成功地进行了荷载传递性状的连续观测。本文介绍该桩的地质条件、桩身埋设的量测元件以及历时两年半的观测成果。观测表明，该桩在不同荷载水平下桩顶荷载的６０％～７０％始终由桩侧阻力分担。这一成果与第一作者先前根据嵌岩桩静载试验结果作出的结论相吻合。     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

循环荷载作用下饱和黏性土的弹塑性双面模型

基于作者新近提出的一种混合塑性硬化准则和临界状态土力学理论建立了一个三维形式表述的适于饱和黏性土的弹塑性双面模型,此硬化准则是著名的M asing方法在三维应力空间中的推广。该模型的二维形式已采用饱和黏性土样室内动态三轴不排水剪切试验的结果进行了验证并已在另文发表。本文所建的三维弹塑性动本构模型与一个半经验的孔隙水压力增长模式相结合,通过有限元程序ABAQUS*对一个循环荷载作用下的条形基础下部地基土层内的位移、应力分布和超孔隙水压力随时间的变化进行了分析,计算结果表明模型预测的地基土的力学响应是符合实际的。     

冷41-平14"L"型水平井轨迹优化与控制技术

冷41-平14井受地面条件的限制,靶前位移小,为保证中间套管和完井管柱的顺利下入,剖面设计为“反向造斜-稳斜-降斜-正向造斜-水平段”的“L”型。简要介绍了冷41-平14“L”型水平井的设计概况,详细介绍了该井井眼轨道优化设计原则和设计结果,以及实钻井眼轨迹连续控制技术。该井精确命中A、B靶,两靶处的井斜角、方位角和垂深等达到了设计要求,在A靶实现了软着陆。该井井眼轨道优化设计和井眼轨迹控制技术为类似水平井的井眼轨道设计和轨迹控制提供了有益的借鉴。     

多孔粒状铵油炸药在边坡预裂爆破中的应用

通过工程实践，介绍了利用多孔粒状铵油炸药进行边坡预裂爆破的设计原理及施工工艺。该技术能确保预裂爆破质量。简化施工工序，大幅度降低爆破成本。技术经济指标优越。     

膨胀水泥浆体系在苏丹1/2/4区块水平井固井中的应用

随着苏丹1／2／4区块的深入开发，为了加快开发主力油层，提高原油产量，降低钻井成本，GNPOC在此区块布置水平井开发任务。所开发的区域主要分布于Heglig，Munga，Simbir，Bamboo区块，油层所在是Zaqar和Bentiue地层。此层位具有高渗透，地层温度高，易塌、气窜等复杂问题，尤其是Heglig和Munga地区井壁坍塌严重。为此，根据地质资料、井身结构和对水平井注水泥的技术要求，科学合理设计施工工艺，优选出适合此地区固井施工的冲洗液和隔离液，特别是经过努力实践，开发出了新型膨胀水泥浆体系，此体系具有高强度、低失水、无析水、防气窜之功效。结合使用哈里伯顿CPT—Y4大功率固井车，精确计量和自动密度控制，该体系水泥浆目前已在7口水平井施工中得以应用，均为优质井。现正在被大量使用，此体系的开发，解决了该固井技术难题，创造了中国固井在海外首次水平井作业一次成功的历史记录，具有较高的经济和社会效益。     

水平井眼轨迹对气井出砂趋势及工作制度的影响

出砂是影响油气井正常生产的重要因素之一。借助FEPG有限元程序自动生成平台，建立了三维应力场弹塑性地层出砂模型，并运用有限元法计算分析了不同轨迹的裸眼井井壁周围的有效塑性应变分布规律及出砂趋势，研究了气藏压力衰竭对完井方式的影响。研究表明，水平井眼轨迹对出砂有重要的影响，同一地应力环境下向不同方位延伸的水平井在投产时应该采取不同的生产压差和不同的生产制度，水平井眼轨迹对出砂的影响程度随着3个地应力差异的增大而加剧。气藏压力衰竭对井壁的稳定性和出砂趋势都有重要影响。随着气藏压力的衰竭，井壁稳定性将变得越来越差，最终导致井筒出砂。因此，对气井完井不仅应该考虑到气藏开发初期地层的稳定性状况，而且还应该考虑到气藏压力衰竭后可能出现的井壁失稳问题。