轴快流CO2激光器气体压力控制

激光切割对激光功率模式、功率密度和功率稳定性要求很高,采用轴快流CO2激光器时,控制工作气体压力工作在最佳状态并保持其恒定是激光器输出连续、稳定功率的必要条件和关键技术之一。在深入研究激光器工作原理和影响激光输出功率因素的基础上,采用带积分分离的智能PID控制算法对工作气体压力进行调节。该过程控制算法简单实用,可以有效地提高气体压力控制精度,改善功率控制精度和稳定性,并用实验加以验证。     

基于PLC电液比例控制的液力测功装置开发及其应用

本文介绍一种齿轮动态加载试验规范及技术要求，论述了运用电液比例控制技术所设计的液压加载系统原理及其使用效果，并简述由此构造的液力测功装置的原理与应用前景。     

小型静压桩压桩力系数取值方法的探讨

由于《建筑桩基技术规范》 (JGJ94 - 94 )和《锚杆静压桩技术规程》 (YBJ2 2 7- 91)表达的不少概念和立足点有着根本区别 ,因此目前在小型静压桩设计、施工、质量检测和施工验收时相关人员在引用规范和规程时出现了不尽统一的现象。本文根据相应规范、规程的有关规定 ,结合现场试验 ,进行分析探讨 ,提出了小型静压桩压桩力系数的取值方法。     

泄压注浆法在治理小型突水中的运用

七煤集团建设工程公司在施工辽阳铧子石膏矿主、风井井筒时 ,多次采用泄压注浆法成功通过中小型含水层 ,对小型突水进行了有效封堵 ,取得了较好的经济效益     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

确定异常高压气藏地质储量和可采储量的新方法

基于文献[1]的定容，封闭，异常高压气藏的物质平衡方程式，提出了确定异常高压气藏原始地质储量，可采储量和采收率的新方法，通过实例的应用和对比表明，提供的新方法是适用的有效的。     

低渗透油藏生产井关井测压时间的计算与应用

低渗透油藏的生产井压裂后，在单井试油试采过程中，压力恢复测试关井时间不同，其中有些井压力恢复曲线不能出现边界反应段，渗流不能反映地层中真实流动特征。针对这种情况，基于长庆绥靖油田塞39井区长：低渗透油藏大量试井和实际生产资料，利用现代试井解释理论，研究合理关井时间的界限及其计算方法。结果表明，当油井关井测压时间达到3倍地层径向流开始出现的时间后，利用此时的压力数据解释地层参数和地层压力，其结果的误差小于5％，同时能较准确地判断边界类型。计算的理论曲线和霍纳法解释值非常接近，对于塞39井区，若预先知道某生产井地层有效渗透率值，可从理论曲线查出压力恢复试井的关井时间，否则，建议按照该井区地层有效渗透率（大约在6mD左右），将不稳定试井测试时间控制在25d以上为宜。图4表3参14     

A new surface characterization technique: RIMAPS (Rotated Image with Maximum Average Power Spectrum)

This work introduces a new imaging technique, Rotated Image with Maximum Average Power Spectrum (RIMAPS), for use in determining orientation and characteristics of surface topography. It consists of computing the maximum value of the averaged power spectrum, given by one step of the two‐dimensional Fourier transform, for each angle of rotation of a digitized image. The basic measurement science of this technique is described and different cases are studied. The characterization of simple geometrical figures explains the meaning of peaks and their angular positions given by RIMAPS analysis. A known surface pattern made on a sample of pure copper, mechanically ground, is used to study reproducibility, dependence on image quality and topography scale relative to pixel size and magnification. Samples of pure zinc, mechanically ground and chemically etched, were used to show the main features of RIMAPS analysis when characterizing a more complicated pattern on a real surface. All the studies performed under different conditions for observation and acquisition of images give strong evidence of the stability and robustness of RIMAPS as a technique for the characterization of topography.     

低压低渗气藏钻探过程中的保护方案

针对鄂尔多斯塔巴庙区块低压低渗气藏物理特性复杂的情况，推荐一套切实可行的气层保护方案。即实行全面钻井液监控；采用欠平衡钻井技术；储层保护前期研究；采用与地层流体配伍性好的阳离子钻井液体系；降低钻井完井液的滤失量，API滤失量小于5mL、高温高压滤失量小于15mL、固相含量小于8％、含砂量小于0．3％；根据储层裂缝的宽度和走向使用保护剂；对裸眼完钻的气层利用洗井清除井壁附近的污染带，恢复储层原始渗透率；固井作业防止气窜；采用具有抑制地层水敏、速敏保护气层的优质射孔液；水力压裂优化压裂设计，严格压裂施工。总之，气层保护技术是一个系统工程，任何一个环节的问题，都将对气层产生伤害．因此需加强气层保护研究，做到在钻开气层到投产的每道工序都采取积极有效的气层保护措施。     

Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.