铀工业指标研究的几个问题

本文介绍在铀矿床工业指标制定中,对未来矿山开采设计方案及经济计算参数几千问题的分析,以利于合理的制定铀矿床工业指标,为铀矿冶企业技术改造,在建企业修改设计和为选择新建企业提供决策依据,进而使铀矿冶企业提高经济效益。     

Ti 离子注入 LiNbO_3表面光学性能

本文研究了 x,y,z 三种切向的 LiNbO_3单晶片注入350keV 高能 Ti 离子(注入剂量为1.5×10~(17)/cm~2)后的表面光学性能。利用光谱仪及 AUEL 椭偏仪对三种切向 LiNbO_3试样在不同工艺处理后的光透射率及折射率进行了测试。注入损伤造成的光损耗可通过热处理消除,使晶格结构恢复至与完整晶格排列相近;注入层的折射率可增加11—13％左右。     

渭河流域水利水保措施减水减沙效益初步分析

截止1989年底,渭河流域共有水库361座,塘坝2666座,引水有效灌溉面积40.4万公顷,治理总面积8136km~2,治理度17.1％。以1970年为效益计算起始年,并将全流域划分为18个片,分别采用水文法和水保法计算1970～1989年间各项水利水保措施减水减沙量及综合减水减沙效益。水文法算得的综合减水效益为24.1％,减沙效益为30.6％;水保法算得的结果相应为29.9％和30.8％,两者相近。     

UL简介与CCL认可

本文从六个方面对UL的基本知识作了一个简要的概述及CCL认可过程的介绍,希望能为业界同仁提供一个参考方向。     

长江中上游地区土壤人渗速率的空间分异研究

利用双套环法对长江中上游水土流失严重区的50个县（市）进行原他测试，对其典型土壤的稳渗速率及其影响因素进行了分析研究。结果表明：土壤稳渗速率在长江中上游地区呈现规律性的地域分异，四川盆地以及毕节地区是稳渗速率高值区，陕南和陇南地区、三峡库区以及丹江口库区足稳渗速率一般区，金沙江下游地区以及湘东赣南红壤丘陵区是稳渗速率低值区；上壤稳渗速率随土类发生有规律变化，黄壤系列土类最大，然后是石灰土、紫色土，红壤系列土类稳渗速率最小；土壤稳渗速率与质量密度呈负相关关系，与孔隙度、大于0．25mm风干土水稳性团粒含量、有机质含量以及粉／粘呈正相关关系。     

基于过程能力指数的刀具寿命研究

利用Glejser检验方法拟舍出刀具磨损过程残差模型，在此基础上，计算换刀时刻的过程能力指数，并且根据企业所要求的最低过程能力指数，计算刀具的质量寿命，提出将刀具的切削寿命和质量寿命结合起来进行换刀决策的方法。     

Crack Development in Individually Quick Frozen Cut and Peel Carrots

ABSTRACT:  Crack development during freezing (CDF) is one of the major challenges in individually quick frozen (IQF) cut and peel carrot processing. The effects of processing and freezer storage on crack development were examined on the cut and peel carrot variety, Sugarsnax. Carrot samples were removed from the major processing steps, the trans-slicer, the shaper, the blancher, and the dryer, and examined for crack development by measuring percentage cracked, crack morphology, total soluble solids, moisture levels, and membrane injury index immediately after processing. These parameters were also examined following 20 wk of standard freezer storage for cut and peels. Approximately 2% of nonprocessed carrots were cracked compared to 45% of carrots after the initial trans-slicing stage. As the processing continued, cracking decreased due to the removal of the outer epidermis to 16% of the finished product. This suggests that CDF was initiated at the 1st processing stage. Crack width and depth were 2.3 and 2.6 mm, respectively, at the trans-slicer stage and decreased to 1.1 and 1.8 mm at the end of the line. It was found that CDF was further exacerbated by freezer storage due to inefficient water removal at the dryer stage. Crack width and depth increased to 1.5 and 3.0 mm after 20 wk for freezer storage. Root size also played a role in CDF, suggesting that larger pieces are more susceptible to crack development. Total soluble solid concentrations did not play a role in crack formation during cut and peel processing.     

Index of critical points in rational l-approximation

This article is concerned with the l²-approximation of a given transfer function f by a rational one whose order is prescribed. We show that the sum of the indices of the critical points of the criterion is generically equal to 1, and in particular does not depend on f.     

Structural reliability optimization using an efficient safety index calculation procedure

The objective of this paper is to conduct reliability-based structural optimization in a multidisciplinary environment. An efficient reliability analysis is developed by expanding the limit functions in terms of intermediate design variables. The design constraints are approximated using multivariate splines in searching for the optimum. The reduction in computational cost realized in safety index calculation and optimization are demonstrated through several structural problems. This paper presents safety index computation, analytical sensitivity analysis of reliability constraints and optimization using truss, frame and plate examples.     

激光探针监测半导体器件内自由载流子浓度调制效应

介绍了基于自由载流子对介质折射率调制作用,而建立的监测半导体器件内自由载流子变化情况的实验装置,该装置能实时反映自由载流子变化情况,且对原电路无任何影响。本方法适用于硅和砷化镓材料的电子和光电子器件,也显示了在测量集成电路内部有源器件特性方面的潜在应用前景。