变压吸附制氧设备真空风机入口压力低分析和处理

介绍了邯钢动力厂真空变压吸附制氧设备的工艺流程,从切换阀本体、电磁阀及仪表气源等方面分析和总结了真空风机入口压力低引起系统联锁停车故障原因,并介绍了相应的处理措施。     

高压低温先导式安全阀的设计

介绍了一种某试验系统用高压低温先导式安全阀,主要从工作原理、结构特点、材料的选用、结构特点、试验等方面进行阐述。     

55t/h锅炉技术改造成功经验

介绍了35t／h锅炉扩容改造为55t／h非标锅炉的技术成功经验。从增加锅炉的容积、受热面面积、燃烧器喷嘴改造三个方面介绍了对锅炉本体的改造，改造后实现了锅炉的水位、汽温及燃烧自动调节，提高了锅炉的热效率为以后的锅炉扩容改造提供了实践经验。     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.     

基于PLC的焦炉集气管压力专家控制系统

通过对焦炉煤气集气管压力系统的分析研究，提出基于专家系统的集气管压力协调控制方案，使得系统在传统PID控制的基础上，能够按照系统实际运行状况智能选择控制策略。全部系统基于西门子S7系列PLC构成，并采用PROFIBUS电缆组成总线型网络。     

VPI粉云母带的选型试验研究

为电机主绝缘VPI工艺选择合适的粉云母带，对几种真空压力浸渍(VPI)用云母带进行了试验研究，分析了选型原则，同时对比了几种粉云母带的性能。将它们应用于模拟线棒中，线棒的试验数据表明：选出的两种云母带的配合可获得优异的性能，达到优等品标准水平。再将少胶云母带应用于电机整机试验，试验结果表明达到了减薄绝缘、降低温升、延缓绝缘老化、提高电机使用寿命的目的。     

静压下ZnS：Te中Te等电子陷阱的发光

研究了4块ZnS：Te薄膜样品(Te组分从0．5％到3．1％)的光致发光谱在常压下的温度特性．对于Te组分较小的2块样品观察到2个发光峰，分别来自Te1和Te2等电子陷阱；而对Te组分较大的2块样品则只观察到1个来自Te2等电子陷阱的发光．我们还研究了这些发光峰在低温1．5K下的流体静压压力行为．观察到与Te1有关的发光峰压力系数比ZnS带边的要大很多，而与Te2有关的发光峰压力系数则比带边小．根据Koster-Slater模型，价带态密度半宽随压力的增加是Te1中心有较大压力系数的主要原因，而Te1和Te2中心的不同压力行为则是由于压力对两者缺陷势增强的不同效果引起的．     

压力计探测液面法探讨

针对油田地质特征复杂，易结蜡，测试中易出现假液面等情况，为准确快速测得液面资料，提出压力计测试液面法。该方法可作为回声仪测液面方法的有效补充。     

液氮制冷低气压试验箱的仿真设计

在采用液氮制冷的低气压试验箱的设计中,用常规工程设计方法计算的降温过程冷负荷过大,从而导致真空系统设计容量过大。本文采用分布参数模型对试验箱低气压条件下降温过程的冷负荷进行了精确仿真模拟,以此作为真空系统容量设计的基础,减小了设计规模,取得了良好的效果。